1 1 2 pvc to garden hose adapter 3d models
2904803 3d models found related to 1 1 2 pvc to garden hose adapter.
thingiverse
A 45 degree Y-adapter for 1-inch schedule 40 PVC to two 1/2 inch barbed hose connector. ...I designed this for the return line on my reef tank where space was limited.
thingiverse
Created half inch male garden hose threads adapter to 1/2" barbed fitting. Fits Tight. ...Posted F3d file from when I designed with Fusion 360
thingiverse
I needed an adapter from a garden hose to shower (1/2" IPT - Which is the standard us size) for my Jacuzzi tub. I could not find one. I used the adapter below to go from the garden tub faucet to garden hose (has a quick disconnect feature), b/c I...
thingiverse
***Background*** : This component was designed in order to be able to install a Bidet Shower into my garden hose. This is quite useful since now I can use the pressure from the Bidet shower to clean up my terrace without changing much on the garden...
thingiverse
I am using this in my RV to adapt the exterior shower hose to a garden hose so that I can hook up an outdoor Fillet Table that has a sink and faucet. ...Cost: $0.48 Print Settings Printer Brand: RepRap ...
thingiverse
Allows for the attachment of a 1.25 pool hose to garden hose print the o-ring using TPU
thingiverse
i modified the garden hose to screw it with a 1" filet
thingiverse
This is an adapter from Garden Hose Thread (GHT) to 1/2" Barb. Fits 1/2" Inside Diameter hose I recommend using a standard garden hose gasket to minimize leaks. ...
thingiverse
Need to back flush the block on the tractor. ...This should do it.
thingiverse
1/2 0.5 inch (approx 13 mm) hose barb to male garden hose adapter
thingiverse
Needed a sump pump adapter so I could connect it to my garden hose. Going to experiment with this. ...Not sure if it'll be sturdy enough but will see
thingiverse
Garden hose to 1/2" flexible tubing. ...Use teflon tape on the male threads to make watertight.
thingiverse
This will connect to the male end of a garden hose (or spigot) and allow you to attach 1/2" flexible tubing. I printed this out and tested it. It worked great to attach the tubing after I boiled one end to stretch it over, but the female garden...
thingiverse
This is an adapter to allow many plastic finials with square insides to adapter to a round 1/2" PVC pipe. This fits inside the center of the center of the PVC pipe. Use Gorilla glue to connect to the pipe and finial Printing: Printed with PETG. 3x...
thingiverse
Just a litte adapter to go from a 1.25 currugated pool hose to a 3/4-11.5 garden hose. Did this so I can use the pool pump to empty out the pool. ...Also see my 1.25 hose adapter to taper on the inlet of the pool hose.
youmagine
... and the "work around" was more than $10. I got the threads for the PVC from mcmaster and the garden hose threads form the link to thingiverse. ...To clarify, this is a female 3/4" GHT (Garden Hose Thread) to male 3/4" NPT (National Pipe Thread).
thingiverse
Customized version of https://www.thingiverse.com/thing:3764039 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3764039
thingiverse
This was designed to speed and ease the install of automatic irrigation systems Instructions After printing drill the small connectors with a 2mm drill
thingiverse
Customized version of http://www.thingiverse.com/thing:125509 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=125509 Instructions Using the following options: h0 = 80 r2 = 13 th = 2.5
thingiverse
This is an adapter for use with a standard pool vacuum hose and a 1" Schedule 40 PVC Pipe. The pool vacuum hose connectors are not standard plumbing fitting sizes, and my non-standard setup requires some... adapting. Just insert a 1" pipe into the...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=560647 Instructions Using the following options: large_end_outer = 58.42 small_end_inner = 35.306 large_end_len = 25 small_end_len = 30 small_end_outer = 38.1 center_end_len = 20 large_end_inner...
thingiverse
> >But my pump came with a BSP 1 1/4 (1.25 inches) thread, I didn't want to buy some pipes or adapters while lockdown. > >Use sealant thread tape, and it works perfectly ! (this kind of pump is not made for that use, it lack a little of pressure,...
cults3d
But my pump came with a BSP 1 1/4 (1.25 inches) thread, I didn't want to buy some pipes or adapters while lockdown. Use sealant thread tape, and it works perfectly ! (this kind of pump is not made for that use, it lack a little of pressure, but...
thingiverse
1 1/2" npt to garden hose adapter with a cone shape inside for extra strength. ...I used it to connect a temporary sump pump to a garden hose.
thingiverse
3/4-11.5 NH (Standard garden hose thread in the US and Canada) to 1/2" hose. This design can accept a standard garden hose washer to create a seal between the drain connection and this adaptor, but this may not be required in some cases. This was...
thingiverse
The hose barb is sized for a 1/2" hose and the threads are ¾-11.5NH (US and Canada standard). The hexagonal section is the same size as a 16mm nut (24mm between the flats). ... You will need a gear clamp to attach it and it may require quite a bit of...
thingiverse
(Remixed from Chanceb94 "Garden Hose to 1/2 inch connector" which printed out at 3/4 inch and had no base for washer (so I hope this is an iterative improvement). ... If you downloaded prior to aug 18 /14 please do again as I had to strengthen the...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=97238 Instructions Using the following options: bandsawLength = 24 $fn = 45 vacuumLength = 25 insideVacuum = 63.5 wallThickness = 2.5 outsideBandsaw = 36