18650 to 21700 battery adapter sleeve 3d models

18650 to 20700/21700 adapter, uses the standard (5mm length) [stainless steel actuators](http://analogboxmods.ca/Box-Mod-Parts/Switches/Up-Down-Switches-Actuators/SS-Actuators) as a contact, either the 8mm fire button actuator or the 4mm up/down...

A simple adapter to run an 18650 battery in a mod that takes 2170x batteries. Just drop a couple coins (i used 3 dimes) in the bottom, then stick your battery in (positive end first) into the adapter and stick in your mod. **NOTE: Use this at...

Battery adapter to be able to use a 21700 battery in a 26650 battery tube. Created to use for a torch. Infill doesnt matter its all walls. ... Probably print with a brim, didn't try without.

I created this to test 18650 and 21700 batteries with the YR1035+ device

Work in progress adapter to convert an 18650 cell to a 21700 cell. You need 1x 5mm M3 screw. Shorter if you want it to be the dimensions of a flat top cell. ...

A simple stand for your 18650 or 21700 Batteries.It can hold 24 of them.If you like check out my other designs too!

This is the first model I'm sharing to the prusa website! Infill 20% zigzag.0.2mm layer height.no supports.Brims for Rods for better adhesion.Filament used in photos - Overture PLA Professional Green.Printed on Ender 3 V2Fastened with 8x M3x10...

Adapter sleeve to allow an 18650 battery to fit into a 26650 slot. Printed using the default Dynamic Quality profile in Cura. ... I used a skirt to make sure the nozzle is clean, but it's not necessary.

18650 to 26650 Battery Adapter H = 16 mm S = 0.5 mm

Simple Adapter to allow 18650 to have the same diameter as a D cell battery. ... I used this to convert a Maglite to use 3 18650 cells.

Adapter to use 18650 battery in place of a 26650. Test print last night and it didn't quite fit. New upload has slightly larger ID and is a little shorter. I reduced the height to 60mm so that the battery will stick out the end a little. I also...

I found a flashlight that uses 26650 battery but I only had 18650 batteries. ... So it was an easy job to print a rough adapter to get 18650 cell centered inside the light.

This is a simple battery adapter to "convert" (dimensions-wise) 16650 battery to 18650 battery. My 16650 battery was not tight enough when placed in the flashlight so I decided to make a simple adapter for perfect fit. I printed this with 0.4mm...

... flashlight. ... 18650 to 26650 battery size. The dimension of my battery was 18.5mm on my flashlight has a 27mm chamber / bore. ... The 60mm long print is shown but it could be a hair shorter if you want and I've included a 50mm length adapter also.

This is a simple battery adapter to "convert" (dimensions-wise) 16650 battery to 18650 battery. ...My 16650 battery was not tight enough when placed in the flashlight so I decided to make a simple adapter for perfect fit. I printed this with 0.4mm...

... 18500 batterys in my isdt charger. ...just cut an m4 screw to the correct length and charge your battery is the isdt charger. on one adapter i cut out a little piece to fit into the charger (the upper port has a closely location, check the pictures)

I made this because I needed a way to carry an adapter for a 21700 battery and two 18650 batteries. But a 21700 battery fits in just as well as the 18650 + adapter, as that's kind of what the adapter does. Fit is very snug as I didn't put ANY play...

I've been experimenting with 18650 and 21700 li-ion cells in my quads so cobbled these up to help build packs. They can be used as soldering jigs and removed after soldering and before shrink wrapping the pack or left in place to reinforce the pack...

21700 to 26650 adapter I needed one for my flashlight.

Just a simple 18650 battery sleeve for my generic Anker flashlight to keep the battery from rattling around.

Sleeve to allow you to use a 27A 12v battery in place of a 23A 12v battery for some fan and car remotes among other things. 27A and 23A batteries are the same voltage and the same length but the 27A is smaller around. This adapter slides over the...

Used to easily and accurately cut 18650 battery shrink wrap covers to 74.5mm. ... The shrink wrap used was purchased on Amazon with the caption of "12M 29.5mm Width PVC Heat Shrink Wrap Blue for 18650 Battery Blue".

A thin sleeve for 18650 batteries to prevent shortcuts during transport. Print in vase mode/1 shell, no top layers, 4 bottom layers, 0.5mm extrusion width. 100% for inner part resize x and y to 109-110% for the outer part I have added a longer...

14500 to 18650 Battery Converter / Adapter Converts a 14500 sized battery to 18650. This allows you to use/charge your 14500 battery with a 18650 device. The design allows you to slide the battery in/out easily. I used copper tape as conductor. ...I...

I could not find any other adapters on Thingiverse that allowed the replacement of three C cell batteries with a single 18650, many of them replace the three C cells with two 18650 cells, I believe that this is most likely to damage an LED...

They are there to ensure all brass spacers make connection with a batteries, even in 3S or 6S setups. Be gentle with them. Caps and sleeves can be connected with rubber bands (<=4mm), M4 screws and nuts, or M3 press inserts. Do not over tight. ...

I could not find any other adapters on Thingiverse that allowed the replacement of three C cell batteries with a single 18650, many of them replace the three C cells with two 18650 cells, I believe that this is most likely to damage an LED...

This adapts a single 18650 in a 2 D cell flashlight. ...Or print two of everything, to work in a 4 D cell flashlight.

By using a LED insert for your Maglite with 3-18 Volts DC you can power those with 1-3 18650 cells while a 5-25 Volts DC insert requires at least two 18650 cells in row. You should consider using 18650 cells with integrated protection circuits only...

You should consider using 18650 cells with integrated protection circuits only as unprotected 18650 cells have spectacular short ciruit current ;-( I have not tried out the D-Cell to 26650 adapter but it should work as well. The quad D-Cell adapter...