2014 f 150 cell phone mount 3d models

F-150 Coin Holder Phone Mount. ... Works on 2009-2014 Ford F150.

I used cheap disk magnets from amazon (1 1/8" diameter). This fits on the dash of my 2013 Ford F-150 and should fit on any F-150 from the 2009-2014 model years. I used 3M double sided foam tape to adhere it to my dash. ...The curve isn't quite perfect...

Ford focus cell phone mount Samsung S7 edge phone Printed in PETG Works great

This is a magnetic phone mount I designed to hold my Pixel 2XL with pitaka case. It holds it on there pretty well and it has only fallen off during offroading. ...I used cheap disk magnets from amazon (1 1/8" diameter).

This is the base for a cell mount for a 2014 RAM 1500. It installs without permanent modification of the truck, in a weird mystery slot in the center console. It's very close to a 12V socket in the console, to connect a charger. I have no idea...

This is the base for a cell mount for a 2014 RAM 1500. It installs without permanent modification of the truck, in a weird mystery slot in the center console. It's very close to a 12V socket in the console, to connect a charger.</p> <p>I have no...

For 2009-2014 Ford F-150 that do not have a Brake Controller. This will replace the rubber mat that is in that area. The phone dimension is 9.6mm thick and approximately 84mm wide. Basically it will fit my Iphone 7 Plus with a TPU case. I build...

This is a remix to use the passenger side, and otherwise useless, coin holder for larger cell phones in cases. I modified the original in TinkerCad by extending it, rotating it out towards the driver, and adding stiffeners to accommodate larger...

This is a mid poly 3D model of a Ford F-150 RAPTOR 2014

Ford F 150 Super Crew Cab XLT 2014 Printable Car in separate parts

It can be used with any double sided mounting hardware that is 2.25" X 1.375". In this case I used a magnetic mount that can rotate. 12-5-22 = Added version 2 (V2) that changes the angle. ...The change in angle makes it easier to snap in and out.

This is a wall mount for cell phones. I designed for a oneplus one, but it fits cell phones with maximum 7.8 cm of width. ...(5.5'' screen)

I designed this mount to replace the Bontrager Insta Mount that holds the cell phone to the bike with double faced tape because it fell off more than once and I did not like the extra mount permanently attached to my phone case. With this mount; I...

Since I'm planning on using a cell phone in it with wake-eye software for auto-recording I figured I'd just design and print a cell phone holder. I made it wider so you can use padding to protect the phone from scratches. A folded coozie can cover...

Scosche brand cell phone swivel mount with adhesive base, magnetic phone mount and metal adhesive plate. Metal plate sticks to back of phone and contacts magnetic mount. Lock nut tightens collet around ball socket joint.Purchased from Amazon - MAGKIT...

This is used for clamping a Carson Cell Phone Eye Piece mount to. It is the largest setting capable of the clamp. Sometimes the cellphone weight, and the size of the eyepiece makes for weak contact, and there a lousy image, between the phone and the...

I created this cell phone mount to hold my phone (Nexus S) while I use it as a GPS or a speaker phone. It clips to one of the bars on the vent, if the clip doesn't fit, the sketchup model is attached so you can make the modifications. The arms slide...

My Ford has a cubbyhole in the dash. ...I created a phone mount that fits in this hole.

... on my 10/22. ...It was designed for a Oneplus 2 and for my BSA Sweet 22. The phone adapter is larger enough that it could accommodate other phones too as long as the camera is centered on the phone. ...Please watch the printing and assembly here:

I would assume the mount would work other phones in other cases since the arms have a fair amount of flex in them. The only non printed part is the nut, which is pressed into place after printing. Print instructionsI printed this using PETG, but...

Simple OpenScad parameteric design with captured 1/4-20 nut Designed last minute before going on a vacation Just measure the max width of the phone in portrait position(pictured) or landscape and change the "length" variable also Measure the max...

This is a mount for my 2010 F-150 without the navigation screen. It fits in the slot where the radio screen is without any extra attaching method needed. I am printing on an ender 3 so I split it into two parts but I also have the single piece...

INVENTOR 3D MODEL OF CELL PHONE LOCK MOUNT STAND

https://youtu.be/YmEXkE7dmN8 Cell Phone Mount for DualShock4

... phone as you can see in the pictures. What you need to use the mount: - Roam Bike Phone Mount - (2x) 1/4"-20 x 2" SAE bolts - (4x) 1/4" Washers Note: I couldn't find black bolts so I coated them with 3 layers of black spray paint before installing.

... ...http://www.thingiverse.com/apps/customizer/run?thing_id=52734 Instructions Using the following options: flat_bottom = 1 stick_thickness = 2 Font = write/orbitron.dxf hole_radius = 1.5 font_thickness = 3 message = F-150 stick_width = 5 font_size = 10

I designed this part to adapt a universal cell phone mount. ...I wanted to mount the holder on the stem and the included clamp was too small.

Updated wall mounted cell phone holder. The other I created fit a phone the size of a Samsung Galaxy Note 8. But that phone has since died and I needed a slightly wider version to fit my S23 Ultra. So this is what I came up with for a quick remix....

This is my first submission and wanted to give back so be kind. ... I recently bought a 2018 f-150 and the phone holder really didn't work so designed this simple holder. it is attached by 5 small pieces of velcro. ...Hope this is helpful to someone.

... Instructions Modeled using Cubify Design, Printed on a Printrbot Simple, no support material required. Printed from the back surface up to the "fingers" holding in the cell phone.