25 kg filament spool 3d models
350475 3d models found related to 25 kg filament spool.thingiverse
This is a center hub for the standard 2.2 kg spool. Including the wrench to hold it tight. ...The remaining axe is 25 mm diameter.
thingiverse
The spool holder is designed to hold spools with a width of 25 mm and a hole diameter of 40 mm up to a width of 100 mm, a hole diameter of 90 mm and a spool diameter of 350 mm. This should usually cover all bobbins from 0.25 kg to 4.0 kg. To build...
thingiverse
This is a filament feed for up to 5 kg filament spools. Also works with standard 1kg spools of filament. i would suggest printing the axle with thick walls. maybe 1mm thick or more. ...make sure you randomize the z axis start point so the dots dont...
thingiverse
Flament spool for 0,5 kg material. spool weight of about 75 grams. ... Screw M3x30mm 3 pcs.
thingiverse
1 Kg abs filament spool holder compatible with: -spool with diameter not greater than 200mm -spool with inner diameter between 50mm-60mm Post-Printing
cults3d
this is a spool holder designed for 3 to 5 kg filament spools you can scale it up as much as you want and fit bigger spools as well you have to print 2 pieces of part 1 and 1 piece of part 2 and read the text included Have a great print
thingiverse
Flament spool for 0,5 kg material. spool weight of about 65 grams. ... Screw M3x30mm 3 pcs.
thingiverse
spool for filament - great for 0.5kg 1.7mm 14cm x 14 cm x 4 cm 5.2cm diameter middle hole
thingiverse
Er hat nur wenig Platz, deshalb sollte der Halter an die Decke geschraubt werden und er benützt 2 Kg Spulen. Als Achse kann man M8 Gewindestange benützen oder eine alte Linearlagerwelle mit 8 mm Durchmesser. Es giebt Spulenrollen mit und ohne...
thingiverse
Needed a larger (longer) holder for my new spools. ...haven't printed it yet..
thingiverse
Stojak na filament. ...Zaprojektowany pod 3kg szpule firmy Colorfil.
thingiverse
Here is an spool holder you can fix on a desk or at the celling of you printer cabin. ...Just press in M6 nuts and place it where ever you want.
thingiverse
... 30.8 × 28 × 28 cm 4 pcs 13.8 × 28 × 28 cm 2 pcs 13 × 28 × 28 cm Cut and sand the wood, drill holes. Screw together with universal screws 3×16 mm. For holding the spool itself you will need a piece of HT tube DN 50, length ~19 cm. ...
myminifactory
this filament role stand is small enough to fit entirely on almost any printbed, and thus is also only about a 3.5 hour print... ... the foot and the leg must be added twice and possibly sanded a bit afterwards to fit together the two legs fit into the...
thingiverse
A spool mount (roller) for a large filament spool (2.6kg). ... Designed for a spool by Hafner-spools (SD 300K) such as the one you get from DAS FILAMENT [https://www.dasfilament.de/filament-spulen-xxl/](https://www.dasfilament.de/filament-spulen-xxl/)
thingiverse
Edit 03/01/2020 Création d'un Capuchon_v2, ----------------------------------------------------------- Un retour d'impression, ça fera toujours plaisir. Pieds V1 réalisé en speed sur Thinkercad pour bobine de 8Kg de chez Arianeplast...
thingiverse
I only had 2,5 kg Spools so I change the holder for spools with a wide of 12 cm
thingiverse
I'm using it with a 2.2kg Hatchbox filament spool, but it should work on any with a 2.25" opening in the spool and a 1" shaft. It takes a bit of force to get them in the spool so they stay in there well. ...Print Settings Printer: ...
cults3d
Center ring to add to the 1 kg Plast.ar filament spool to shrink the center hole to 28mm.
thingiverse
Stock Filament Spool Holder (Spindle) is too short for 1 kg Spools. ...I directly copied the geometry of the Holder installed from Ultimaker 2+ Connect and extended the length.
thingiverse
This is a spool holder for the xxl spools from Das Filament: https://www.dasfilament.de/filament-spulen-xxl/ The spools are evil @ the first meter's but then all is fine ;-) My 2 prints failed because the spool wasn't in a holder during the print and...
prusaprinters
Big filament spool holder for 2,6 kg or 1 kg spoolsYou can simply place the spool holder or screw it on the IKEA Lack printer enclosure.To change the filament, simply remove the screws on the top and slide the spoolholder out to the...
prusaprinters
This is a spool holder for the xxl spools from Das Filament: https://www.dasfilament.de/filament-spulen-xxl/ The spools are evil @ the first meter's but then all is fine ;-) My 2 prints failed because the spool wasn't in a holder during the print and...
thingiverse
Modify shaft to fit your ball bearings. ... min. 50% infill due to thin body. use: 3 x M3 screws, filament guide and body ass. ...
thingiverse
This is 3D model of filament spool stand for big filament spool of 2,3 kg (spool outer diameter of 300mm). Becouse the those spools are so big for our 3D printers we design soluton for it... You can download and STL files for 3D printing and after...
prusaprinters
The friction-fit has a tolerance of 0.1 mm so please make sure your printer can handle that. 1-kg-half 110x33.stl: This design fits the old Prusa Whitelabel-Spools (not Prusament) as well as other Spools with 110mm Diameter and hold 12 Games Workshop...
thingiverse
Hi, No ball bearing needed, just a printer and some PLA. ... Use the screws from the original CR-10 holder. Works fine There is too, a spool holder 2.3 kg to put on a table (same axes for the 2 holders)
thingiverse
Anet A8 Plus roll holder for 1 kg rolls with 50 mm inner diameter. ...Two-part, one print, self-rolling.