2nd gen tacoma head unit 3d models

Had to lengthen and flatten the clip a bit to make it work for the Tacoma head unit bezel. Gray PLA prototypes in picture were too short and would break or pop off into the dash. Yellow cip is the original I found under the cup holders (same clip...

I designed these cupholder inserts to fit in the 2nd gen tacoma. ...There's 4 different models available: 2 Yeti Hydroflask_Left Hydroflask_Right 2 Hydroflask

Tacoma 2nd Gen replacement knobs for heat controls and 4x4. ... The fit was pretty tight, took a lighter to warm up the inside of the knob where the shaft slides in to make a perfect fit.

The knobs without bolts have holes that can be tapped and real M4 bolts added, the other version has the bolt heads printed into the part. There is also a 4WD knob to match. I left a slit in the knobs for the light to shine through for night driving....

center console organizer for 2nd gen toyota tacoma with false bottom

Designed a holder/charger that fits in the little coin tray next to the shifter of the 2nd gen Toyota Tacoma 2005-2015. I added space to insert one of the wireless charging chips you can get from China. I got mine from AliExpress for about $4. I'll...

I created this based on the idea found I believe from the 4Runner's and adopted it to work with my 2nd Gen Tacoma (2009.) I built using PLA at 0.2mm layer height and it looks great. I would recommend 4 solid top & bottom layers & 2-3 outlines. Been...

Blank switch inserts for the center console of a 2nd gen Toyota Tacoma (2005-2015) I designed this for my under-seat subwoofer install to have a clean bass volume adjustment knob. I have included STEP files to make it easier for you to customize your...

Cup holder divider for 2nd Generation Toyota Tacoma. When I purchased mine, it didn't come with the cup holder divider. I didn't have XM Radio, so I modified http://www.thingiverse.com/thing:1098040 Second file is a bit taller and seems to fit...

Switch blank for a 2nd Gen Tacoma center dash. ...Print a .2 res and 0 infill.

Switch blank for a 2nd Gen Tacoma center dash. ...Print a .2 res and 0 infill.

Thread in adapter and funnel for the 4.0 2nd Gen Tacoma Funnel is from https://www.thingiverse.com/thing:980665/files

I have included a 1 piece file which you can do a layer change on for the different colors, or 2 separate pieces if you prefer to print them separately and glue them together after May also fit the facelifted 2.5 Gen Tacoma as well (2012-2015) but I...

These mounts are to fasten the Dasaita Head Unit to the 3rd Gen Toyota Tacoma. The factory mounts require significant bending in order to allow the factory bezel to fit properly over the new head unit. ... (6) M5x14 FHCS (Flat Head Cap Screws) are...

I have included a 1 piece file which you can do a layer change on for the different colors, or 2 separate pieces if you prefer to print them separately and glue them together after May also fit the facelifted 2.5 Gen Tacoma as well (2012-2015) but I...

Low profile ditch light bracket for 2nd Gen (2005-2015) Toyota Tacoma. Mounts to hood hinges with factory hardware. I printed at 80% infill with tri-hexagon pattern on ender E3 and it has been strong enough. Mounting location gives about 1.5 inches...

This is an insert for the cup holder just behind the shifter in the 2nd generation Toyota Tacomas. This was designed to hold two rows of quarters, a pen, and a Leatherman Style PS or CS. ...Feel free to leave some suggestions or request changes!

This is a 3d scan of the head unit trim on a 3rd gen (2016+) Toyota Tacoma. ... This isn't meant to be printed but instead as a modeling aid for designing parts to attach to it.

This is a fuse block and winch switch mount for the 2nd Gen Toyota Tacoma (2005-2015). I bought a Badlands 12k winch and needed a way to mount a 350amp Mega Fuse and the on/off switch within my engine bay. This mounts up on the drivers side behind...

Adapter for Brightsource Amber/White Raptor style LED's that allow for 3M Double-sided Tape or screw to the grille Light link: https://brightsource.ca/product/super-slim-marker-light-amber-white-s20sm4aw/

3D printed cup holder for gen 2 tacomas

This is a design for window mounting 120mm fans from the interior window frame screws in a Snugtop camper shell. Increased ventilation while out and about. One file is for the top 2 screw of the frame, the next for the bottom 2 screws, and then air...

This sits in the coin tray and hangs over the edge a bit to hold a wireless charger and a phone, currently sized to a pixel 4 with a case. Haven't printed it yet, but thought I would get it out there if anyone was interested. Will update once...

This is a design for window mounting 120mm fans from the interior window frame screws in a Snugtop camper shell. Increased ventilation while out and about. One file is for the top 2 screw of the frame, the next for the bottom 2 screws, and then air...

This sits in the coin tray and hangs over the edge a bit to hold a wireless charger and a phone, currently sized to a pixel 4 with a case. Haven't printed it yet, but thought I would get it out there if anyone was interested. Will update once...

<p>This sits in the coin tray and hangs over the edge a bit to hold a wireless charger and a phone, currently sized to a pixel 4 with a case. ...&nbsp;I hollowed out the bottom to decrease the print time and maybe put some weights in there if the weight...

This is a switch blank for non TRD first gen tacomas to cover the hole where the locking diff button should be to the left of the steering wheel by the gage cluster dimmer knob

Model of the Nest Mini 2nd Gen.

A stand for Amazon Alexa 2nd gen

This is a 2GB 2nd gen iPod Nano