3 8 hose fitting 3d models
1253236 3d models found related to 3 8 hose fitting.grabcad
Brass barbed hose fitting with ferrules on both ends to hold 3/8" ID hose. ...Slip on hose and secure with hose clamp, zip tie or adhesive depending on pressure, wall thickness and material of hose.
grabcad
1/2" Female NPT brass hose fitting for 3/8" ID hose. ...15/16" hex.
grabcad
Brass hose fitting for 3/8" ID hose. Ferrules on barb end hold hose from slipping off. Use of hose clamp helps prevent leaks. 1/2" Male NPT thread on opp end. ...7/8" hex
thingiverse
It adapts 3/8-inch NPT to 1-inch ID hose. I designed a single-barb adapter and a 3-barb adapter. I included a solid and and hollow version. The solid version may be useful if you want to drill a single diameter hole through the adapter. I...
thingiverse
Needed an adaptor to connector a small (12') 5/8" drain hose to my AC drain outlet (3/4" PVC pipe). Printed with threads facing print bed and no supports. Not sure if you could prime and glue it like normal PVC pipe but, for my use (no pressure...
thingiverse
This is a pneumatic air line hose clip that requires no gluing & has a hidden fastening (#6 Countersunk Screw) Simply print both parts, screw the bottom to your wall, insert the hose & slide the top part into the groove to secure it
thingiverse
Water cooling fittings use mostly 1/4" / 6mm OD push fittings, or 3/8 / 8mm ID barbed fitting, I designed these elbows 6mm (tapers down to 5.9/5.8mm ID and 8mm barbed to 10mm OD, allowed some space for pex crimp ring , or worm gear hose clamp, some...
thingiverse
3/8" (or ~10 mm) hose extender 8 mm inner diameter Support not needed.
grabcad
Grease Nipple for 3/8" port with all details including retracting spring...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: output_size = 0.375 inputs = 1 input_size = 0.375 input_barb_count = 3 inline_junction_width = 0.8 connector_type = inline outputs = 1 strength =...
thingiverse
3/8" to 3/8" Hose Clip. ... Print with ABS in high heat situations
thingiverse
This adapter is for a 3/8 inch inside diameter hose, pretty tight fit but I use a clamp as well just for the heck of it. I printed using support and 50% infil just to keep it pretty rigid. You could do more infill if its too weak, luckily its a...
grabcad
Stainless Steel Hose Connector, 1/8 in. Swagelok Tube Fitting, 1/8 in. ...Hose IDSoft Plastic and Rubber Tubingbarb end
thingiverse
The threads are 1/8" NPT and the hose barb is approximately for 5/16" rubber vacuum hose I think. Should work with 1/4" too I guess. ... Instructions Printed at .1 or 0.05mm layers in ABS, worked well...
cults3d
Hose joints with hex fitting tapered Outside diameter 0.8 mm Inside diameter 0.4mm Print tested on Photon mono x6K with nFep film In profile available some different diameters 1.6, 1.4, 1.2, 1.0, 0.8
thingiverse
Hose fitting * One: >Width: 19 mm >Height: 140 mm * Two: >Width: 19 mm >Height: 120 mm # ** Raft two or more layers! ...**
thingiverse
These hold a pair of 3/8" ID hydraulic hoses together. The OD on these hoses is ~3/4". Two styles are provided. The one clamp holds the hoses just with friction. You only need to print one of these. This is the one with the "bunny ears" The second...
thingiverse
This is a simple 8 mm beer hose push-In fitting circlip. I've tested it with Duotight 8mm fittings (highly recommend, super high quality fittings) and DMT / DMfit 8mm fittings, and it works pretty well for both. I recommend printing this using...
thingiverse
The bottom of the connector is **3/8" ISO** pipe threaded. * The connector is **waterproof!** * Tested and working values: Layerheights: **0.15** or **0.2** or **0.32** [mm]. Infill: **15** or **20** [%]. PLA temp: **200** [Celsius]. Bed...
thingiverse
This is a clip for 3/8 pneumatic rubber hoses. I designed it to route my airline in my garage. I usually put them 16'' apart, the hose snap in place for a good hold, ceiling or wallmount. ... You can either print it in PLA or PETG, 50% infill.