308 bore guide 3d models

I printed this bore guide to help my brother clean his .308 hunting rifle with ease.

Tool designed to fit an LR308 chambered in .308 Winchester or 7.62x51mm NATO to prevent unnecessary internal barrel throat wear from use of cleaning rod. ...May or may not fit other rifles

Bore Guide for the Bergara B14R

bore guide for cleaning a rimfire bergara

CZ 457 Bore Guide for use when cleaning,

This is a 10-22 bore guide to protect you muzzle from damage when running a cleaning rod down the barrel. ...This was a modification of the barrel cap designed from imfurplay.

Bore guide to be used cleaning a Model 1894 Marlin rifle. Should be considered a beta/prototype. A bit of a tight fit when new, can easily be tapped into or out of the action. My first spin with AutoDesk 123D, so the part was modeled with a metric...

Keeps Cleaning Rod in Center Alignment & Protects The Bore Slip onto the cleaning rod before installing the brush or mop. ... 12 Gauge Bore

Useful tool for cleaning bore.Designed to print as one or two parts - for Z 210mm limited printers.

This is a muzzle guide to fit on the flash hider of a M14 or M1a rifle. ...It is designed to fit a Dewey .30 cal cleaning rod, and keep it centered to minimize contact with the crown.

Blaser R8 .300 Winchester Magnum Bore Guide

Bore guide specially done for Sauer 101 in 308w.

a pegboard holder for a tipton bore guide kit.

This is a bore guide for cleaning the 10/22 takedown, it is notched and has a solvent port for brushes/patches.

Designed for 308 but should work for other cartridges.

Bore guide designed to limit muzzle damage from cleaning rods, for use with the M1 rifle. ...This guide is designed for a more secure fit than those that can be purchased from commercial vendors, as it indexes off the gas cylinder lock screw.

Cleaning rod bore guides for the Ruger Precision Rimfire in straight up and down and 20 degree rotation solvent port (haven't tested the 20degree one yet) to allow for easier insertion and minimize damage to the chamber. I have my cheek piece up...

Customized version of https://www.thingiverse.com/thing:3023372 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3023372

308

Winchester .308

Bore guide consists of two parts for easy printing on small printers. First part has one solid layer at the bottom for the easy bridge printing without supports, just cut out a hole when printing will be finished. ...All parts have been made to fit...

I modeled 3 bore guide tips for cleaning your rifle. I measured these with a caliper to make them as accurate as possible. The "BoreGuide tip 22" is for sizes .22 to .30 I recommend rotating these objects upright in your slicer before...

Print Parameters: Printer: Ender 3 Layer Height: 0.2mm Wall Thickness: 1.2mm Infill: Recommend 10-20% Material: PETG Amazon Basics Black Temps: 240C Nozzle @ 85C Bed Retraction Distance: 5mm with Z-hop Enabled Supports Enabled - Touching Buildplate...

Adjustable bore guide for .22 centrefire up to 30 CAL. Print the part: * BoreGuide_main And depending on your calibre: * BoreGuide_end_22CF-25CAL * BoreGuide_tip_22CF-25CAL or * BoreGuide_end_26-30CAL * BoreGuide_tip_26-30CAL For...

customized with 3D Slash!

customized with 3D Slash!

customized with 3D Slash!

customized with 3D Slash!

Designed for Big Bore shock absorbers, mounted on Inferno VE 1:8 with 19.5mm internal diameter springs If you find it functional, leave your positive comment Thank you

308