3d bridge
1652711 3d models found related to 3d bridge.
grabcad
A 72 meters long bridge. Beam bridge (15+21+21+15). 6 beam(in section). ...used for visualization(lumion)
thingiverse
this is the class project that we use different infill of percentage to make a bridge. ... Our load to weight ratio is 500/1
cults3d
This is a duct you can add to your existing bridge fan without adding a new fan to channel air directly to the tip of the print head. ...Tolerances are tight so make sure it does not hang lower than your print head.
thingiverse
This is a duct you can add to your existing bridge fan without adding a new fan to channel air directly to the tip of the print head. Tolerances are tight so make sure it does not hang lower than your print head. ...
thingiverse
This is 3d printed bridge. ...You need metal vex shafts to fully assemble.
thingiverse
The 3D printed bridge which printed with 85% infill. ...Itself has 29g and it held 897 times weight than itself, which is 26kg
thingiverse
A 3D Printed Bridge that spans a 5 inch gap. It has a load-to-weight ratio of 470. There are 34 total members to this bridge. ...One surprise was that some members have trouble fitting due to unsatisfactory rotation space.
thingiverse
This is a 3D printed bridge that can support over 100 times its own weight. The members in the still file section above this description are printed as follows: Members 1 and 3=100% infill, members 2 and 4=30% infill. The load to weight ratio of...
thingiverse
this is a 3d printed bridge held together by metal shafts used to test the strength of a bridges design. it was able a bucket. this can be in different colors and can be used for what ever you want. all pieces have an infill of 95% and it weighed up...
thingiverse
This is a design for a 3D printed bridge. The designed length is 6 inch and the weight is 22.1g. According to the test, it can hold up to 22.4kg with a load to weight ratio a little bit over one thousand. STL files for each unique individual member...
cgtrader
3d bridge model Sketchup 2020 model burak yaşar
cgtrader
3d train bridge for your train models layout indoor and outdoor
thingiverse
The adapter for smaller inner diameter by Kningzer was almost perfect to fit a Taulman 3d Bridge filament spool onto my Monoprice Maker Select v2.1 - however, it was just slightly too short. I've extended it. Please use the nut from his project...
thingiverse
These are two members that I designed with my partner for a bridge project at school. ...There are two unique members and there are two assembly files that have all the parts needed to make the bridge.
thingiverse
... ...This means that the load to weight ratio is 454. the longer members were printed at 70 percent infill while the shorter ones were printed at 50 percent infill. The problems were that the bridge was too high which made it weaker and easier to break.
thingiverse
0.9 100%infill 2.012 100%infill 2.54 100% infill 1.8 100%infill 1.8 75% infill 2.012 75%infill The max load radio for the bridge : 200% The bridge max load : 27lbs (4 pieces of rock)
thingiverse
In addition there is an stl with all 1.4 inch members and one stl with all 1 inch members required for the bridge. Both member types were printed at 100% infill. In total it weighs about 26.5 grams and can hold about 9.7kg. ...This means that the bridge...
thingiverse
i worked with Jeremy Zwingman on this project and it is a bridge with varying members of size and infill. the two different files represent the different types of infill of 25% or 50%. The total weight of our bridge was 20.5 grams and it had a weight...
thingiverse
Weight of bridge: 39g Load held: 33kg(that's the maximum weight. ...We may hold more) Load to weight ratio: 841 Members with 10% infill are 1.27, 1.8 and 2.012 Members with 15% infill are 0.9 and 2.846
thingiverse
The members of this bridge have either an infill percentage of 75% or 100%. The load to weight is 200. Make sure you have a good printer or you will get printing errors. ...We have a blue member because we accidentally broke a member and borrowed one...
thingiverse
There are two types of members 100% infills with a .195 diameter 75% infills with a .2 diameter Load to weight ratio : 380 Surprised and problems: I accidentally made a bridge that was too complicated for my skill set. Also my partner, while making...
sketchfab
pont de la caille 3d photogrammetry bridge annecy haute savoie
prusaprinters
Bridging is your printer's ability to print a layer between gaps in lower layers without support, essentially printing over thin air, creating a "bridge." It is essential that your 3D printer can properly bridge because many prints require some...
thingiverse
... different length and infill. ...Most of the members are 80% infill. The 100% infill member are for some high pressure point. Load Weight Ratio: 600 The process of building bridges is hard. ...Also, the whole distance of the bridge was decrease a lot.
sketchfab
Bridge Photogrammetry Pont de l’Abime 3D - photogrammétrie annecy haute savoie