3d print overhang

This is a 3d printing calibration tool I designed. The design inherently asks a lot of a printer, and can be used to identify potential problems before wasting filament on a messed up larger print. The stl is in mm. ... Make sure to like and...

Just another 3d printer test cube. ...10mmX10mmX10mm

I have been working on adjusting my printer settings so I drew this part up so I could see what type of draft I can print.

If your printer can print this, it can print almost any overhang. ... This allows you to test whether your printer can print an overhang without it looking sloppy.

  Customizer for testing print overhang quality. Based on the same concept and design as the Massive Overhang Test by thingster ( http://www.thingiverse.com/thing:40382 ), but this version is customizable. ...You can generate free floating overhangs or...

Customizer for testing print overhang quality. Based on the same concept and design as the Massive Overhang Test by thingster ( http://www.thingiverse.com/thing:40382 ), but this version is customizable. ... You can generate free floating overhangs or...

Customizer for testing print overhang quality. Based on the same concept and design as the Massive Overhang Test by thingster ( http://www.thingiverse.com/thing:40382 ), but this version is customizable. ... You can generate free floating overhangs or...

... is standing on one corner. ...The three cylinders are attached to three sides of the cube.The print can also used to test roations on X,Y,Y-AxesOn two of the three pictures, you can see, the difference of the overhang by using different printer-speed

A test print to check the printers overhang possibility by printing a cube and three cylinders. The cube is standing on one corner. ...The three cylinders are attached to three sides of the cube.  The print can also used to test rotations on...

... is standing on one corner. The three cylinders are attached to three sides of the cube. The print can also used to test roations on X,Y,Y-Axes On two of the three pictures, you can see, the difference of the overhang by using different printer-speed

... standing on one corner. The three cylinders are attached to three sides of the cube. The print can also used to test roations on X,Y,Y-Axes On two of the three pictures, you can see, the difference of the overhang by using different printer-speed

... diameter, the starting angle (I did 35) and width/height of the cross section. ... Print this hollow. I got better overhang results the slower I went. Also .2mm worked better than .1mm for me. ... The shown photo is 20mm/sec, .2mm, sliced with Cura.

I have used this to test the overhang ability of my Makerbot Replicator 2X. ... I print it horizontal instead of vertical like it is shown in the preview. Also scale the model to whatever is going to push your printer. ...I scaled 1.5x for mine.

A strange test print. ...The blue picture is the inside of the file.

Angle overhang test for 3d printing.Ranges from 90* to 44*, two angles, one degree per side.

I just needed the overhang test, so i removed all other areas.

A customisable overhang test - i haven't finished cleaning up the wedges yet, but hopefully it will be useful enough. Allows you to customise the thickness of the sections, the angles, the number etc. ...

I just trimmed the profile to reduce the print time to less than half for the same results. ...

Meant to test the printer's ability to print overhangs with the roof and it's ability to retract filament in between the columns on the print, also it's ability to print bridges as it starts to build up the roof in between the columns. This thing...

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following options:...

Advanced bridge test

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following options: _end = 75...

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following options:...

Use as is.

Customized version of http://www.thingiverse.com/thing:58218 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58218 Instructions Using the following options:...

Use as is.

An Easter-themed model that is designed to stress test your 3D Printer. Fair warning: this is not an easy print! If you liked this model, why not try out our other stress tests too?Print Settings:For this challenge, you can use whatever...

A simple model to test the unsupported printing performance of your printer/polymer combination. ...There are a bunch of similar models on Thingiverse but not as an editable CAD model.

This part is for testing 3D printer settings. It has 5 walls that are 15, 30, 45, 60, and 75 degrees from the build plate. These walls are labeled on the top of the part, and they provide reference for determining when support structures are needed.