3d printed pin hinge

3D Printed bowling pins, material: PLA, good toy for children to play.

It's a hinge that can only made by 3D Printing. ...The screw in the middle is for tightening the hinge to door, the screw is attached to the clamp, and can't be removed except with force.

The second one (and last two pictures) is a design-edit for a 3D Printed Pin in wich a standard tapel pin can be added. Dimensions are: 74,8 mm (Y), 56.6 mm (X), 42.3 mm (Z) For more specific 3D extensions and renderings, contact me! ...Please, feel...

This is a small but functional 3d printed hinge that I made, and it can be used for many different applications

Another concept of hinge that can only made by 3D Printing. The concept is to use grip like side to attach to door. The grips are flexible that can be moved by gear inside the hinge. The gear is rotated by L (socket) key. ...The gear shaft has threads...

A small hinge to be mortised into a wood case. ...Gives a minimal look that i like</p>

I printed it with a material called HCPLA, but probably they work well on normal PLA too, keep in mind that ABS is much more brittle, so probably they'll not work at all or will not last more than 10 times, also ABS loses its flexibility overtime,...

You can print it continuously as long you need. Easy to print and assembly. ...Strong design.

Material : ABS Plastic (or another recommended material from 3D Printer Manufacture)I'm open for criticism for improve this submission until get the best solution.You can see my other entries for that challenge in this link bellow :- 3D Printing...

3D

Easy to print and with endless possibilities for matching colors.

Hinge for a greenhouse I made. ...Works nice. You will have to use a small piece of wire as hinge. Made in Fusion360. ... Filament: Redline PLA

I also added a threaded 4mm hole on one end so it can be pulled out easily. Hope this is useful to others, total print time was about 4.5 hours with my printers settings. Print Settings Printer Brand: Anet Printer: A8 Rafts: No Supports: No...

... part with a diameter of 9.8mm to account for my printers inaccuracy. ... I also added a threaded 4mm hole on one end so it can be pulled out easily. Hope this is useful to others, total print time was about 4.5 hours with my printers settings.

I chose to coil the 3D printed "wires" (red and green) around the hinge pin and use the coil as a strain relief and service loop. The wire path could be used for fluids if left hollow. Note: Since flexible, conductive polymers compatible with...

... mount gears -- benefit being the use of nuts to pin elements firmly in place for more complicated/torque-requiring activities. I will print some pin connectors and share the STLs here along with recommendations for settings for Tony's OpenSCAD tool.

Slide pin to hold our P6 and P7 chastity devices closed. These fit where ANY standard chastity lock cylinders usually fit. ...Once it is in place, a small padlock can go into the end.

Easy to print and with endless possibilities for matching colors.

Hinge Pin Bushings

Pin through hinge

Plastic hinge pin

Added a printable pin for the 3D Hinge for Creatbot DE/DX Series by AP_Patipat. Print with material fitting of the need and environment. ... Pin is longer than hinge to allow for easy removal.

Customized version of https://www.thingiverse.com/thing:2187167 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2187167

The original does not have a hinge pin so I whipped this item up. ... Print two (one for each hinge)

3mm Hing Pin for Arduino Case.

Hinge pin , part 3 Source: tracepartsonline.net

Simple taper pin hinge. ...40mm tall, 62mm wide (assembled)

This is a replacement hinge pin for a trashcan

Rotating hinge that has a pin for locking an angle. ...Use for your generic hinge needs!

Hinge pins to replace missing garbage can hinge pins. They both broke immediately. ...Will try again with higher density.