3d printed xbox controller phone mount

A replica of an xbox controller. Modeled in Maya. ...You will have to scale up and rotate 90 degrees.

Key Facts: * Should work for most modern-day smart phones * Made from only two 3D-printed parts and one rubber band * Use stick-on foam strips to stop the mount from pressing your phones volume/power buttons. May not be an issue if your phone is in a...

Modification of Xbox One Controller Phone Mount by WhatTheActual01. This rotates the phone 90° as some games require. It will hold nearly all of the latest larger phones. ...The end notches also have been resized to hold a phone with up to a 12mm thick...

... fine. chopped this together really quick as i liked the idea and i didnt see any other mounts like this. I used chickenbisket's quadlock head model that they made (Thank you!) as its very well made. ...https://www.thingiverse.com/thing:1257384

Number of parts you have to print: 1 x Part1.stl 1 x Part2.stl 2 x Part3.stl 1 x Part4.stl 1 x Part5.stl Other pieces: 1 x Hex Bolt M5 x 25mm 1 x Nut M5 1 x Elastic rubber band 4.5mm width

Advantages over similar designs: - phone above the controller (not on top of it) for better balance and ergonomics while still giving enough room for your fingers - snap-on fit - single part - designed to be extremely easy to print, no supports, no...

Xbox Controller Phone Mount ==================== Customized for POWER A wired xbox controller --------------------- -Should fit any xBox One Controller --------------------- -Designed with tolerances in mind, so there shouldn't be any problem fitting...

This is a remix of the Xbox One modern controller mount made by @pixel2 adapted for using with the Modular Mounted System made by @HeyVye. In my experience the best Xbox controller mount with the best phone mount out there. Pros Easy to set-up and...

Remix of jerwil's Xbox One S Controller Phone Mount to accept a Popsocket rather than clamping on edges of the phone. ... Sized for a Pixel 2 XL, though should work with most other models -- a larger phone may not slide in all the way but still hold...

This is an Xbox one S controller mount compatible with the [Modular Mounting System](https://www.thingiverse.com/thing:2194278). So you can use it with the phone clamp ! It's a remix of the very good [mount by CrazyRandomS...

This is simply a remix of the item "Xbox One [XB1] Controller Phone Mount", thing 4162196, that has the lame branding "Red Iron" like what is even the logic? it's hidden, it's just lame. so I added a box with PrusaSlicer and exported the same stl. no...

This [wired 360 controller mount](https://www.thingiverse.com/thing:2553504) was the inspiration for using the GoPro-style joint and the phone clamp is from the [Modular Mounting System](https://www.thingiverse.com/thing:2194278). I'm using...

This is simply a remix of the item "Xbox One [XB1] Controller Phone Mount", thing 4162196, that has the lame branding "Red Iron" like what is even the logic? it's hidden, it's just lame. so I added a box with PrusaSlicer and exported the same stl. no...

I purchased this Xbox Series X phone adapter from Amazon https://www.amazon.com/gp/product/B08LYY43DN but the angle was horrible. This adapter provides a more comfortable viewing angle and covers the bright Xbox logo. ...This is not a full mount - just...

... It clips onto my Xbox Series and Xbox One controllers just fine although it is a slightly better fit on the Series controller. Holds my phone well and feels securely connect to the controllers. It is a little more flimsy when not on a controller.

just sliced up the parts of previous version and re arranged them to put the phone above the controller. ...just slightly more compact.

This is a custom phone holder for a DJI Phantom 3 Controller. It is designed for the Moto G5 Plus phone (with outer case installed) but probably will work for many phones of similar size. Worst case you could model and print custom clips for your...

Flexible xbox controller phone holder. Works best on newer model Xbox S controller with usb c port. Hold nearly any sized phone. ... Print with PLA and no infill.

I made this holder because i wanted to have at the same print both my phone and my xbox controller

This adapter lets you mount your phone on to an original xbox controller in the memory card slots. To connect an phone, cut the controller cable off and splice on a usb cable (leave the yellow wire disconnected), and then use a microusb otg adapter...

This is a remix/mix of two Xbox controller phone holders that I liked a lot. I liked both designs, so I decided to customized them a bit to create my own phone holder. I recommend priting at 60 mm/s (if using an Ender 3) and to use as an infill...

Thanks to Running_Banana for summarizing the parts you need to print: 1x Xbox One Clip with Modular Mounting System 1x Phone Clamp Up with Tab 1x Phone Clamp Down 1x M5x25 Bolt 1x M5x65 Bolt 2x M5 Nut 1x M5 Knob Short 1x M5 Knob for Phone You get...

I wanted a controller mount for my phone, but wanted a more secure method that didn't interfere with any buttons, so I modified the HTC Vive Tracker mount (https://grabcad.com/library/htc-vive-tracker-support-to-hold-on-an-xbox-one-controller-1)...

I found the Xbox One Controller Phone Mount by Isummers to be one of the best looking and simple prints. A few things with the original design made me want to do a remix. 1 The first issue was the space left at the top of the controller was still...

Xbox Controller Wall Mount

This is a mount that connects a ZTE Speed Phone (probably works for others) to a Logitech F310 gamepad (probably works for others). It has spaces for wires to be wrapped around and a Monoprice 4-Port USB 2.0 HUB to be fitted into place. This was made...

this is a remix of https://www.thingiverse.com/thing:3930816 it extends the mount to accommodate iPad mini and also shrinks to iPhone 12 size other changes include slightly widening the xbox grip as it was very tight and beyond the flex of pla , I...

... with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3gf8q3MvP3E Designed it myself, might fit, made it as sturdy as possible. If it warps during the print, it will still work unless it warped too much. ...Good luck and happy printing!

Wall mount for Xbox wireless controller.

Xbox Controller Mount! ... Have fun :) - DJ