3dprinteros
43 3d models found related to 3dprinteros.
myminifactory
A very classy bow tie duck, print it with Ninjaflex for maximum fun!
myminifactory
Print at 0.2 mm layer height, with 10% infill. ...This uses 7 g of filament and takes 1 hour and 26 minutes.
myminifactory
Print at 0.2 mm layer height, with 10% infill. ...This uses 7 g of filament and takes 1 hour and 19 minutes.
myminifactory
Print at 0.2 mm layer height, with 10% infill. ...This uses 9 g of filament and takes 1 hour and 50 minutes.
myminifactory
Print at 0.2 mm layer height, with 10% infill. ...This uses 7 g of filament and takes 1 hour and 23 minutes.
myminifactory
Print at 0.2 mm layer height, with 10% infill. ...This uses 8 g of filament and takes 1 hour and 38 minutes.
myminifactory
Print at 0.2 mm layer height, with 10% infill. ...This uses 7 g of filament and takes 1 hour and 28 minutes.
thingiverse
Ultimaker Camera Holder for Genius Wide Cam Works with any of the other 3DPrinterOS ducks as well.
youmagine
Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...75 mm/sConnected via Raspberry Pi 2.
pinshape
Ultimaker Camera Holder for Genius Wide Cam Works with any of the other 3DPrinterOS ducks as well.
thingiverse
Not your average duck professor. ... Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...75 mm/s Connected via Raspberry Pi 2.
youmagine
Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...50 mm/sConnected via PC, Windows 8.1 64 Bit.
pinshape
Not your average duck professor. ...Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...75 mm/s Connected via Raspberry Pi 2.
pinshape
A duck prepared for whatever the road might bring. ... Printed on the Replicator 2 at 180 microns in PLA. Sliced and printed at 90 mm/s via 3DPrinterOS. ... No raft or support needed.
pinshape
Duckie who's eligible to dive to the bottom of the seafloor Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...50 mm/s Connected via PC, Windows 8.1 64 Bit.
pinshape
Has a striking resemblance to Bane. ...Probably the most irresistible member of the Duck Dynasty. Printed on the Makerbot Replicator 2 via 3DPrinterOS. 200 Microns, 10 percent infill. ...90 mm/s Connected via Raspberry Pi B+.
cgtrader
A duck prepared for whatever the road might bring.Printed on the Replicator 2 at 180 microns in PLA. ...Sliced and printed at 90 mm/s via 3DPrinterOS.No raft or support needed. ...
thingiverse
Duckie who's eligible to dive to the bottom of the seafloor Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...50 mm/s Connected via PC, Windows 8.1 64 Bit.
thingiverse
A duck prepared for whatever the road might bring. ... Printed on the Replicator 2 at 180 microns in PLA. Sliced and printed at 90 mm/s via 3DPrinterOS. ... No raft or support needed.
cults3d
A duck prepared for whatever the road might bring. ... Printed on the Replicator 2 at 180 microns in PLA. Sliced and printed at 90 mm/s via 3DPrinterOS. ... No raft or support needed.
cults3d
Duckie who's eligible to dive to the bottom of the seafloor Printed on the Ultimaker 2 via 3DPrinterOS. 120 Microns, 10 percent infill. ...50 mm/s Connected via PC, Windows 8.1 64 Bit.
youmagine
Has a striking resemblance to Bane.Probably the most irresistible member of the Duck Dynasty.Printed on the Makerbot Replicator 2 via 3DPrinterOS. 200 Microns, 10 percent infill. ...90 mm/sConnected via Raspberry Pi B+.
thingiverse
Has a striking resemblance to Bane. ... Probably the most irresistible member of the Duck Dynasty. Printed on the Makerbot Replicator 2 via 3DPrinterOS. 200 Microns, 10 percent infill. ...90 mm/s Connected via Raspberry Pi B+.
thingiverse
Inspired by the 3DprinterOS version with fewer parts. Print two brackets to hold the camera on each side. The angle of the camera is set to view the whole build platform of the Ultimaker 2 when it is in the top or bottom position. ...The camera can be...
cgtrader
Video of testing here: http://youtu.be/THZXw_eRSIQThe 35mm file worked with these spindles from Amazon: http://www.amazon.com/gp/product/B002BW1DH4/ref=oh_aui_search_detailpage?ie=UTF8&psc=1We recommend printing the pedal spindle facing side down...
thingiverse
... that one could rest the handsets in the caddy as well. Note, the Quest 2 is pictured with aftermarket silicone protectors for easy maintenance for COVID. This remix was completed using Autodesk Fusion 360, Ultimaker Cura, 3DPrinterOS by Ren Saludo.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=63731 Instructions Using the following options: text_spacing = 1.1 cs_shape = cs_ellipse text_inside = false smoothness = 20 text_enabled = true text_itself = 3DprinterOS text_engraved = false...