3dr solo
6505 3d models found related to 3dr solo.thingiverse
3DR Solo Leg extensions with notches for tire ups to hold the legs more tight.
thingiverse
Leg extender for the 3DR solo. ...I curved the end so that it fits into the Solo backpack.
cgtrader
3D model of the 3DR Solo drone. Professionally reversed engineered to 1 mm accuracy. Workable for developing drone accessories. ...
thingiverse
Custom motor pods for 3DR Solo. No ESC, but LED lights can still be placed underneath the pod. Fits most 2212 motors. ...
thingiverse
Use to cover GPS in 3DR solo instead of cardboard. ...Print Settings Printer: TEVO Tarantula Rafts: No ...
thingiverse
Bracket to mount a standard 36mm x 36mm GPS receiver in the 3DR Solo. ... Use standard screws to mount bracket and drill out holes (if need be) to fit whatever screws you use to mount GPS to bracket.
thingiverse
This is a replacement cover for the 3DR Solo LED Covers. Depends on what material you use will determine the toughness of the locking tabs. Using 3m double sided tape will make the ensure a solid fitment one of the prints has a cutout for a...
thingiverse
Handle for 3DR Solo. You can use Solo as a camera stabilizer. You can also catch Solo during landing. Be careful and use safety glasses! Four M2 screws required. Thread length protrusion into Solo not to exceed 7 mm. ... Weight is about 60 g (with...
youmagine
Simple GoPro caddy to replace the official 3DR SOLO GoPro mount. ...This mount will enable you to use a GoPro for the visual live stream from the drone whilst enabling another camera to be suspended from the craft at the same time.
thingiverse
This is a 3D printed 3DR SOLO gimbal holder. It should can fit in all of the gopro versions with weight added. You can also install the weight adjustment print even with this holder. ... You may need to add some foam to adjust the tightness of the...
thingiverse
This collection comes with a base plate that mounts to screw holes on the bottom of the 3DR Solo while still allowing the gopro gimbal to be attached. Additional plates can then be stacked using common m3 spacers as seen in the photos. I use m2.5...
thingiverse
Balance for 3DR Solo gimbal. Clips to the back for modified or non-GoPro's attached to the gimbal. Use with my 3DR Gimbal Adapter for GoPro-clones (http://www.thingiverse.com/thing:2022659). The stock balance weights screw into the holes. For the...
thingiverse
Adapter for the 3DR Solo Gimbal, allowing you to use a non-GoPro camera. Any clone with the same dimensions as a GoPro should work. This was designed and tested with a Gitup Git2. The Solo Gimbal Balance (http://www.thingiverse.com/thing:2024247)...
prusaprinters
This collection comes with a base plate that mounts to screw holes on the bottom of the 3DR Solo while still allowing the gopro gimbal to be attached. Additional plates can then be stacked using common m3 spacers as seen in the photos. ...I use...
thingiverse
Propeller guards for the 3DR Solo, print with 100% infill. Print upside down with support (>70 deg angles) and make sure the support is properly removed afterwards. The top/bottom dimensions have only 0.4mm gap with respect to the Solo and if the fit...
thingiverse
This is a 3d printed 3DR Solo Charger adapter plug and you can print it out to attach to any 16.8V transformer to charge your Solo battery.
thingiverse
Mounts to the belly of the 3dr Solo, allows for an additional camera/sensor to be used. ... I used this to mount a Parrot Sequoia and use the GoPro with gimbal at the same time.
thingiverse
Purchase upgraded mounts at http://www.maxxuav.com This is used to hold two Sunhans 2.5W Amplifiers & Battery and mount to the 3DR Solo Radio. ...I used amplifier & battery from FPVLR.com
pinshape
3DR Solo Drone Motor Covers As i am needing some pocket money for a new solo battery, ive designed a projectat school made out of abs for the 3DR Solo. ... I've had mine for about a year now and the amount of dust that builds up inside the motors copper...
myminifactory
... printing and designing so alot of my early stuff is going to be remixes of things i think will work well together and weirdly sculpted learning attempts at 3D designing. ...Hope you enjoy!Long Leggs for the 3DR Solo Remixed with R2D2 by Kirby Downey.
thingiverse
This is a remix of the Sequoia mount for DJI Phantom, adapted to work with the 3DR Solo style down-facing GoPro mount system. May be used for other applications, but intended for use with the the Parrot Sequoia multispectral sensor. ...Print Settings...
thingiverse
This is a bracket similar to what Colin Guinn used in the set of 13 hours for his 3DR Solo Drone. ...You will need a nut and bolt to secure the two brackets together or use a couple of zip ties Print Settings Rafts: No ...
thingiverse
I am new to 3D printing and designing so alot of my early stuff is going to be remixes of things i think will work well together and weirdly sculpted learning attempts at 3D designing. ...Hope you enjoy! Long Leggs for the 3DR Solo Remixed with Hitman.
thingiverse
I am new to 3D printing and designing so alot of my early stuff is going to be remixes of things i think will work well together and weirdly sculpted learning attempts at 3D designing. ...Hope you enjoy! Long Leggs for the 3DR Solo Remixed with R2D2.
thingiverse
This is a NADIR mount to attach a Sony RX100 to a 3DR Solo for mapping applications. You'll need the following to complete: 4 ea. - M2x12 screws 4 ea. - Rubber ball dampers 2 ea. ...- Small Velcro Straps or Plastic Zipties