80mm fan duct 3d models
127211 3d models found related to 80mm fan duct.thingiverse
Got sick of my AC68U overheating and none of the ebay fans arriving so I designed this duct for an 80mm fan. ... Hardware: 80mm fan and standard PC fan screws.
thingiverse
This is a duct for an 80mm fan. This made the print worse than not using the duct, but better than a 60mm fan. ...I would suggest no duct.
prusaprinters
This is a duct for an 80mm fan. This made the print worse than not using the duct, but better than a 60mm fan. ...I would suggest no duct. Category: 3D Printer Accessories
thingiverse
For the TL Aluminatus - the deck fan is a pretty hefty 24v 80mm blower, and it creates serious drafts when attempting to print ABS. It's also very, very loud. I did two things to minimize the impact on printing, and as an added benifit, reduced...
thingiverse
minimal stepper driver 80mm fan duct / tunnel for my mks board
thingiverse
A 80mm fan duct for the k8200, supported by clamping it around the E3D and using a screw from the stepper motor. A guide vane increases the pressure for the 80mm fan so it pushes nicely through the narrow spaces. Recommended to print this at 0.1mm,...
thingiverse
This is a duct adapter for an 80mm computer fan to hook to a 3" dryer duct line. ... I designed this to pull the smoke out of my small LED laser cabinet.
thingiverse
For the construction of a case ventilation for a 80mm hose I found nothing suitable. ...Therefore, I quickly created a 80mm fan adapter.
thingiverse
This part created to direct 3d printer system box ventilation hot air to side. ...Make from abs, infill 100%
thingiverse
Attention: print without supports and with good cooling. ... Note: 80mm Fan duct mount for Prusa Mendel i2 Sorry, 80mm...
thingiverse
Fan duct for 80mm fan.This model suit for Micromake delta printer.(20mm aluminum frame) I finished with polyester putty and lacquer paint. ... https://jibundeyarou.com/80fan2/
thingiverse
Customized version of http://www.thingiverse.com/thing:735038 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions Using the following options: n_pipe...
thingiverse
Inspired by the Fan Cover with vent by the user The_Drunken_Chewbacca, I made my own (quick) version of it. ...(With and without support in the middle) Enjoy ;)
thingiverse
... with full cover; * dont sacrifice airflow. I decided to use 80mm fans and and make duct as large as possible. WARNING!!! 80mm fans are usually 12V while stock one is 24V. ...You'll need dc-dc step-down converter (like LM2596) to connect fan.
thingiverse
Simple fan duct to add an 80mm fan to the top of a Western Digital Elements enclosure. The duct is tight around the front and sides and covers the back grill down to just above the power button with a 5mm gap forcing the air to go up and across from...
thingiverse
Adaption of original 40mm design for single 80mm fan. First model using exponential airflow adaption. ...Print Settings Rafts: Doesn't Matter ...
thingiverse
Customized version of https://www.thingiverse.com/thing:373491 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=373491
thingiverse
Customized version of http://www.thingiverse.com/thing:21112 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=21112
thingiverse
This fan duct will send the electronics cooling air away from the heated print bed and eventually out through the side of an enclosure. The mounting screw holes are all placed relative to the corners of the base. You might need to adjust those for...
thingiverse
... The 503870 files I included are sliced flat for better printing, you will need to go to the org thing for the tip. ...Fits this fan perfect http://www.radioshack.com/120vac-3-fan/2730242.html
thingiverse
I decided to use 80mm fans and and make ducts as large as possible. WARNING!!! 80mm fans are usually 12V while stock one is 24V. You'll need dc-dc step-down converter (like LM2596) to connect fan. Connecting hotend fan is easy part. You just...
thingiverse
Boca de cooler 80mm Instructions Using the following options: base_screw_diameter = 4.3 duct_shape = rounded base_screw_margin = 4 fan_size = 80 duct_rotation_z = 0 duct_rotation_y = 0 duct_rotation_x = 30 duct_delta_y = 50 duct_delta_x = 20...
thingiverse
This is a adapter for the prusa i3 Zonestar p802 80mm fan holder and ducthttp://www.thingiverse.com/thing:1470922 It fits the 60mm Fan instead of the 80mm one
thingiverse
... tube ducts, it's great for tight spaces. The duct can be rotated to point the air in any 4 directions of the fan. Slots for the fan cable are measured according to my own fan so your mileage may vary. ... Feel free to do your own modifications.
thingiverse
80mm fan duct for the printer to end all printers. ...Hoping it really kills it for printing PLA FAST AF.