aerosol can straw holder 3d models
1140745 3d models found related to aerosol can straw holder.thingiverse
I wanted something to hold the straws on aerosol cans after use, and I didn't want a holder that wrapped around the can, so I designed this. I printed at 0.1mm because its a small print and doesn't take long either way, I'm sure 0.2mm would work fine...
thingiverse
Modular holder for Aerosol cans. Made for holding Aerosol cans stable in my toolbox. ... Designed for Aerosol cans with a bottom ring diameter of 68mm.
prusaprinters
After seeing one I wanted a straw clip to fit all the WD-40 cans that I had and after next to zero searching I decided to make my ownIts should work for most 660mm diameter recessed rim cansI did print this on my A8 as the tolerances might be off on...
thingiverse
This was designed to hold standard household aerosol cans, almost all14oz cans should fit. ...This uses standard 4mm screw holes so should mount nicely to any surface, it has flat outside edges to allow for double sided taping as well.
thingiverse
I made a couple sets of these for inside cabinet doors to tame unruly aerosol cans. Pretty straightforward to print and use, made for 1/4" (6.35mm for you metric fellers) steel rod I already had, still a little small so drill out to size. Print...
thingiverse
I made a thing. ...Holds a small fire extinguisher can. ...Check out my etsy or something c @ chunks3d
thingiverse
This is a straw holder to hold the straw on spray cans. ...It just slides over the can and there is three different sizes.
prusaprinters
Spray Can Straw Holder wall mount. Print instructionsCategory: DIY
thingiverse
A simple spray can straw holder that takes approx. ...10 minutes to print and weighs about 1 gram.
thingiverse
Aerosol Straw Saver Simple holder for the straw on most aerosol cans. Holds the straw in the ready to use position and will save it (if it pops out of the nozzle) from shooting across the room and under that void that seems to exist in every shop.
myminifactory
Aerosol Straw Saver Simple holder for the straw on most aerosol cans. Holds the straw in the ready to use position and will save it (if it pops out of the nozzle) from shooting across the room and under that void that seems to exist in every shop.
thingiverse
I made this to hold the little straws on the spray cans you buy like lubricating oils, etc. It keeps from losing the straws in between uses and keeps from the straws going flying while using. ...
thingiverse
I have a few WD-40 and other spray cans with straws, tried it and it works! I had some initial difficulty inserting the straw into the hole, it eventually went in. And so I did some design changes in hope of improving the straw insertion. I had...
prusaprinters
I have a few WD-40 and other spray cans with straws, tried it and it works! I had some initial difficulty inserting the straw into the hole, it eventually went in. And so I did some design changes in hope of improving the straw insertion. I had the...
thingiverse
Modeled these 2 straws from scratch using OpenSCAD after another I found on Thingiverse, [https://www.thingiverse.com/thing:4285168] as this one didn't fit my cans. ...Version 2 has a split ring because the DeoxIT can has a rim on the top and bottom...
thingiverse
Handy little thing to help keep track of those little straws that always seem to disappear. ... Must be printed in a flexible and stretchy material to work properly (I used NinjaFlex).
thingiverse
Wall mountable holders for one, two or three aerosol spray cans. ... I found that printing with supports on the upper section gave the best results.
prusaprinters
<p>Holds your containers, meant to mount to a 2x4 and angled slightly for easy access. ...I made in PLA, PETG or TPU or ABS would probably be better though. Fits a WD40 can perfectly. ...Scale up slightly for CRC cutting fluid.</p>
thingiverse
A simple straw holder for any metallic spray can. e.g. wd40, lubricant, ptfe, degreaser, etc. ... Quick to print.
thingiverse
Corresponding straw size: Diameter 3 mm or more, and length 50 mm or more If the spray can is stored on the shelf in the garage, it can be sufficiently fixed with just the claws on the top of the holder. ...Also, if you carry the spray can in a bag...
thingiverse
A simple straw holder for any metallic spray can. e.g. wd40, lubricant, ptfe, degreaser, etc. Did'nt like the clamp on holders. This one work really well. No fiddling. Straw is held in place with just the correct force. simple to move between cans...
thingiverse
I guess I could have fiddled with simply scaling existing ones but that would have ended up causing problems with the straw holder so instead here is my take on the simple and yet obnoxious if you have no way to store it, straw holder for a spray...
thingiverse
... your can. ...There are lots of them already on Thingiverse but the only one that let you insert the straw from the side was for cans much smaller than mine. ...So I made my own using OpenSCAD so it can be easily sized to whatever diameter can you have.