akm rear sight 3d models

hope to get corrected by experts.

Блок прицела к АКМ. ...Сборка прицельной планки не моя, решил сэкономить время и не делать то, что сделано до меня.

hope to get corrected by experts.

Rear Sight Base for AKM

I couldn't find any Picatinny rails mounting on the rear sight block for the AKM/AK47, so I drew up this one. It replaces the rear sight slide as can be seen in the pictures. It is a friction fit. The mounted optic can feel loose-fitting, but that...

Glock Rear Sight Blackout

Baikal MP651K rear sight

M870 Breacher rear sight

REAR SIGHT OF A PISTOL

Simplified Rear Sight Dimensionally Accurate

Rail mounted rear folding battle sight

Kel-tec Sub 2000 rear peep sight replacement

ghost ring rear sight for the WE Tech G17

Here’s the rear sight assembly of my AK model.

This is the tritium night sight, rear assembly for the Sig P226.

Here's a simple model of the SMLE rear sight, to complement the very old SMLE model i made

A widely compatible rear sight for pistols. ...If you  have any issues printing feel free to contact me through Pinshape.

I needed a more stable rear sight for my 80lb hand crossbow. Due to the increased height of using a dovetail to picatinny rail adapter, https://www.thingiverse.com/thing:616483 , I added a lower peep sight and opened the top sight for quicker sight...

Rear sight for Mini 14, the hole size is a little larger than the OEM rear sight but after a few shots with adjustments you can find a zero. ... Also it is designed to use the original screw from the OEM sight.

Rear sight for nerf rails Please process the screw holes according to the screws to be used. ナーフ用レイルのリアサイト 使用するネジに合わせてネジ穴を加工してください 光造形用にデザインされてますがPLAでも一応作れました 元々ハンマーショット用ですがアレはレールの仕様が微妙に違うので 加工しないと取り付けがキツイかもしれません 固定にネジを使いますが当然ネジあとが付きます. ...

AK74 rear sight base I made for an AK project I'm working on. ...Might be usable for an AK47 model?

A rear mp5 sight on a nerf rail adapter edit: please use the new smaller 2.0 version with the hole for the rail nub positioned better

This band gets pressed over the barrel and becomes the base for the rear sight assembly. ...Measured by hand, may not be accurate.

I had to remove the rear sight on my FAL because it interfered with the scope I put on it. ... This simple cover slides in place where the rear sight would be to keep the screws covered and just provide a slightly more finished look.

This is a Replacement non-drift adjustable rear sight for the Walther P-22. It retains the screw from the original sight and takes aprox 10 minutes to print, please use atleast 40% infill. This thing was made with Tinkercad. ...Edit it online ...

Replacement rear sights for the SMK/Snowpeak PP700sa. The grub screw hole is designed for self-tapping. ... Tinker Cad: Original size: https://www.tinkercad.com/things/17ZWymq1dXm Plus 5mm (for use with mods): ...

It is based off of the AR-15 rear sight, but will work fine on any blaster. This is my first make that I've uploaded to Thingiverse, so any feedback is greatly appreciated! ...Print Settings Printer Brand: SeeMeCNC ...

Shotgun Rear Sight Design Based off Browning A5 Dimensions Measure the rib on your shotgun and compare to these dimensions. ... Rib Dimensions - 6.5mm x 2.5mm Print With Sight Dots Vertical on Bed Sight Dimensions - L = 20mm x W 11.5mm = x H= 9.99mm...

This is a replacement rear sight rail for the PGP2. It is intended to be used along with my [PGP2 Front Feed Cap](https://www.thingiverse.com/thing:3541642) and my [PGP2 Feed Plug](https://www.thingiverse.com/thing:3549755). It snaps into place...

This is a replacement rear sight rail for the PGP2. It is intended to be used along with my PGP2 Front Feed Cap and my PGP2 Feed Plug. It snaps into place without permanent modification to the marker. ...It is held centered by snapping into the top slot...