amscope lens 3d models
21620 3d models found related to amscope lens.
thingiverse
The source files are on [github](https://github.com/yoppeh/amscope-lens-containers). This all started when I tried to use the adapter for the 0.5x Barlow lens to allow the LED ring to be attached. The adapter wouldn't stay screwed in to the lens. I...
thingiverse
I will be using my scope everyday and didn't want to be bothered with uncover the whole thing everyday so created these dust caps for the lenses. Uploaded both with and without the eyes. If you're going for the dual color swap print at .2 layer...
thingiverse
Easy to remove and put len cover for AmScope SM4 and similars. Just a box... ... I print with clear PLA
thingiverse
I made this part to replace original lens cover, since my have burn out. ... Use 3 perimeters
thingiverse
An adapter for centering your phone over the 25X lens of the AmScope Microscope.
thingiverse
#Update * 20/01/19 Added Additional Tray for Ø32mm rods * 23/01/18 Added Cableholder for Ø32mm rods * 24/01/18 Added Camera Mount for Trinokular Microscopes, Ø27.8mm Screw Thread on the Lens Side (Tip to get the Ring on the Lens: Print it, Heat it...
thingiverse
In particular the AMScope T490B which it has been tested on, though it should work on any microscope with a similar light diffuser shape. If you want to try some bright white LED light in your incandescent AMScope this is the project for you! The...
thingiverse
(note: this may not be compatible with some AmScope clones without the aforementioned linear bearing) Get rid of the cumbersome and heavy microscope stands that take up your whole desk! You will need 2x 8mm ID x 12mm OD x 15mm Length bushings such...
thingiverse
Inspired by CapTecs vesa adapter, but this model reuses the entire focusing mechanism from the standard amscope boom stand for a faster, simpler print. Use m5 machine screws and nuts. ... Print two brackets and a core, use long m5 screws into the...
thingiverse
This is for Amscope's SM-4T series of stereo microscopes. It levels out the base, so I can sit my soldering station on it. The front matches the curvature of the base. The back goes to the full depth of the base and doesn't round the corners off...
thingiverse
This is a support for an AMscope microscope head, fully customizable. Designed for a SM-3T, but may fit other models. You will need 3x M3 bolts and nuts to assemble the legs to the head support, and a piece of wire to go through the holes at...
thingiverse
Adapter that allows the use of regular eyepieces on the trinocular port of an AmScope microscope. ... This allows the use of eyepiece cameras.
thingiverse
Add a Raspberry Pi camera to your AmScope desktop microscope. Fits exactly over the eyepiece with no additional hardware required. Since every eye piece is slightly different, you'll need to experiment a little to find the best place to mount the...
thingiverse
This C mount male to male adapter was required to get my camera to focus in tune with the eyepieces in my AmScope stereo microscope. The distance is 7.5 mm - which can easily be changed. ... Intended to print without support.
thingiverse
Inspired by @hackerfriendly http://www.thingiverse.com/thing:1514922 and http://hackerfriendly.com/amscope-upgrades/. But I needed it to work with my inspection scope (see pictures) and his design didn't seem to get the right distance for my scope. I...
thingiverse
CapTec (https://www.thingiverse.com/thing:4853500/files) to incude the complete original mechanism of an Amscope or similar microscope instead of dissasembling it and installing it in a heavy/expensive 3D print with 60-70% infill. This solution...
thingiverse
Wiring for LED lights and triscope camera is tricky to manage on the Amscope microscope. I tried gaffer tape and velcro but was never satisfied with the result. This is a pair of cable guides to stop the cables getting caught in the movement. Combine...
prusaprinters
This is a double-threaded adapter to screw a camera module (C-mount 1"-32 UN 2A) on top of the trinocular Amscope extension tube (M26/0.75) you can find on models such as the SM-3TZ-54S.The OpenSCAD file is available and all dimensions are...
cults3d
This is a double-threaded adapter to screw a camera module (C-mount 1"-32 UN 2A) on top of the trinocular Amscope extension tube (M26/0.75) you can find on models such as the SM-3TZ-54S. The OpenSCAD file is available and all dimensions are...
prusaprinters
Wiring for LED lights and triscope camera is tricky to manage on the Amscope microscope. I tried gaffer tape and velcro but was never satisfied with the result. This is a pair of cable guides to stop the cables getting caught in the movement. Combine...
thingiverse
This is a double-threaded adapter to screw a camera module (C-mount 1"-32 UN 2A) on top of the trinocular Amscope extension tube (M26/0.75) you can find on models such as the SM-3TZ-54S. The OpenSCAD file is available and all dimensions are...
thingiverse
Amscope microscope dovetail/M42 ring adapter. ... 2nd adapter is designated to use with the Reichert tube lens, it means Amscope microscope can be converted to use with infinity type objectives for the photography
thingiverse
This mount should fit any of the SE400 series microscopes.(The ones with a rectangle objective lens cover) Here is a link to the LED Light:...
thingiverse
Tube to attach the 'Improved Logitech Webcam to Microscope Adapter' by 'the_digital_dentis' to an Amscope microscope with a lens diameter of 33mm. ... See the original 'thing' for the camera holder and for instructions.
thingiverse
... AmScope Trinocular microscopes. ...It threads into the camera's C/CS-mount (no lens required) and reuses the tube+knob focus mechanism on the scope. Single piece, prints without support and the threads should work even at 0.200mm layer height. ...