anet a8 bed leveling sensor 3d models

Added a slot to the sensor mount for easier and wider range of adjustability.

All of the auto bed levelling sensor mounters is designed to mount in front of the extruder and that makes the look of it very complicated. I designed one that auto bed level sensor will be mounted backside of the extruder and it let you set high of...

Anet A8 Auto Bed Levelling Sensor Holder. This is my second 3D design using Fusion 360. ...Feel free to re-use it.

Made for the original Anet A8 Auto Bed leveling Sensor to fit on these Beltholders: https://www.thingiverse.com/thing:1433295 which i used to upgrade to this bowden setup: https://www.thingiverse.com/thing:2099577 Works just like the original Anet...

A very simple mounting for the Tronxy type inductive Auto bed levelling sensors for the Anet A8. It does not interfere with the extruder fan ducting. ...However, if you have installed belt tensioning devices behind the extruder carriage, it might...

The original support by TNS hits the frame of my Anet A8, so I edited it removing a small part on the right side to prevent collision. ... These are the parameters I set in Marlin configuration: `#define X_PROBE_OFFSET_FROM_EXTRUDER 27` `#define...

Remix to make narrower and prevent collisions with the frame uprights at the x-axis limits

Firmware configuration: Due to the altered sensor position the following changes have to be done in the configuration.h file (search vor the capitalized string and adapt the subsequent numbers):With my E3Dv6 mount / carriage:#define...

Remixed TNS sensor holder to accept Tronxy (or Anet) sensor. ... I haven't used it as i ditched this sensor but it fits nicely.

you will need to change your sensor location offset's in your configuration.h file the new settings I am using successfully: define X_PROBE_OFFSET_FROM_EXTRUDER 48 define Y_PROBE_OFFSET_FROM_EXTRUDER -15 I hope you find this design helpful. ... ...

So I used Tinkercad to modify the STL file in the following way: - Mounting holes are now 4.2mm in diameter - Mounting plate is now 4.xmm instead of 2.5mm (sensor has same distance to nozzle) - The sensor is fixed by two 3mm x 12mm screws UPDATE: For...

The Sensor would not have been long enough to bring it down to sensing range in both mounts So i decided to make the Mount plate a bit thicker for more stability. It is not really needed as the Sensor doesnt move that much, and it is ok in only 1...

Mounted on Anet A8, direct extruder (original) layer 0.2 infill 30+ Used with Skynet3D (Marlin)

The general idea is from LucaCap's rear bed leveling sensor holder (http://www.thingiverse.com/thing:1883473). All credit for the fantastic design and idea goes to him! Nevertheless, the original design requires to tap threads into the metal bearing....

The support has the 18mm hole which generally is the diameter of the capaciteve sensors For the 12mm (inductive sensor): http://www.thingiverse.com/thing:1884118 Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20%...

The support has the 12mm hole which generally is the diameter of the inductive sensors For the 18mm (inductive sensor): https://www.thingiverse.com/thing:1883473 Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 20%...

The uploaded design doesn't have my name on the front. I designed the following fan cover to move my bed levelling sensor which was previously connected to my fan assembly, however, I have now added a door to my fan to allow easier access. Be sure...

This is a Sensor mount for every M12 Sensor that can be used. ...It fits right behind the Cooler, so you optimise your distance between your Cooler and your heat sink.

This is a bracket for the ANET A8 Plus 3D printer to accomodate an auto bed leveling sensor probe. Due to the incline of the fan, it is not compatible with its predecessor ANET A8. It also has a fan cover, so you can reuse the orgininal bolts.

... In a much more durable and tough design. ...Also sensor can be adjusted by turning the 2 sensor's nuts. In the original design that was not possible. Also, print 2 of these even if only one is mounted. Just in case it breaks :) Enjoy. ...

Bed Level Sensor mount for the stock Anet or TronXY bed level sensor, made specifically for the thing it's remixing. V2: Reduced the size of the mount V3: Realigned the mount to be centered on the nozzle. ... Distance from nozzle to sensor...

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of http://www.thingiverse.com/thing:2219963 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of https://www.thingiverse.com/thing:2219963 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2219963

Customized version of http://www.thingiverse.com/thing:2219963 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2219963