anet a8 plus x belt tensioner 3d models

this is a compiled and edited version from several source of Anet A8 plus x belt tensioner works like a charm, just like the original

These files are similar to the stock X axis belt tensioner for the Anet A8 Plus however I had issues with the X axis belt slipping out at times so I upgraded the smaller end of the belt holder so you can loop the belt around the part. This resolved...

The original DIY part was of poor quality, broken. I created it again. ...Later I changed it to fixed.

X-Axis Belt tension replacement for Anet A8 Plus printer. ...One design includes holes for all possible belt heights.

This is a belt tensioner for Anet a8 // a8 plus that use same x axis group. Start from the tensioner from https://www.thingiverse.com/thing:2934446 I'm using a self modified version of a toothed idler by GonzoG that use idler with integrate ball...

Sturdier replacement for the originall x axis belt tensioner. ...I recommend using it with this belt holder https://www.thingiverse.com/thing:4024940 The other end of the belt can be helt by screw and cable tie as shown on the picture.

Bolt Required : 4 of M3 x 0.5 long 26mm + 2 washer 2 of M3 x 0.5 long 9mm 1 of M3 x 0.5 long 51mm + nut

it is the original tension for the X-as. ... print it with support on the plate like the picture.

This is the X-belt tensioner of the Anet A8 plus reviewed and corrected

this tensioner has been designed for the X-axis belt of the anet a8 plus printer, starting from the original design which brings and improves the detail accuracy for the timing belt and screw adjustment, offers a straighter belt tension and improves...

Stronger more beefed up X axis tensioner for the anet a8 plus sticking close to the original design that comes with the printer, featuring looped belt grips with a high matching teeth profile. ... no special sprinting requirements, no supports needed...

belt tensioner for anet a8 plus

Anet A8 X Belt Tensioner Option of larger screw for more tension

Another belt tensioner for the Anet A8. ... Parts needeed : - 1x 50 mm m5 bolt - 1x m5 nut

Same Anet A8 X-Axis Belt Tensioner by WedgeSD desing (https://www.thingiverse.com/thing:1895051) with 3mm holes. Tendeur de courroie pour l'axe X. ...Revue avec un tarreau pour vis de 8

Same Anet A8 X-Axis Belt Tensioner by WedgeSD desing (https://www.thingiverse.com/thing:1895051) with 3mm holes. Tendeur de courroie pour l'axe X. ...Revue avec un tarreau pour vis de 8

Made this belt tensioner for the X-belt, no need for a longer belt to add this item. things needed 1x M4 nut,1x M4 screw 40 mm long, optional a washer and a spring. My Anet A8 came with extra springs in the package same type for the heated bed i have...

X belt tensioner for Anet A8. This is a remix from https://www.thingiverse.com/thing:1683070, which uses 3d printed screws with knob instead of metal ones. I suggest to print this with 0.1 layer height for a good fit of the screws. ... Update:...

This is a redesign of Brisemuth's excellent Anet A8 X-belt tensioner idea. I love that it does not require one to purchase a longer x-belt since it reaches through the pulley support and that it provides tension by pushing on the X-axis bearing rods...

Anet A8 X belt tensioner with a single thumb screw adjustment designed with a low profile as to not collide with the extruder carriage. This was designed to use the spare screws & nuts that came with my printer. ... Required parts: 1x M3 20-30mm...

A tensioner for the x axis-belt on the anet a8. This design is sturdier than the ones i could find and you dont need additional screws for it to function. The used belt when installed is also shorter than the length used in the previous installation,...

"Body1" is a remake part "holder"(in original) for Anet A8 x-belt tensioner for My printer. part calls "gabel", "gabel_pulley"(for a idler) and knob is from original project. ... Material: Aluminum Alloy Tooth: 20 (T) Pitch: 2 (mm) Bore ∅: 5 (mm) Belt...

... length of the belt and thus the necessary tension and vibrations decrease. Following parts will be needed: - 5 x M3 18mm (from Anet kit) - 5 x M3 nut - 2 x washer (for original pulley) Any comments are appreciated. ... Cheers, Brisemuth

This is a simple x-belt tensioner for the Anet A8 printer. I wanted a x-belt tensioner that fulfils following criteria: * G2 geared tooth pulley should fit (the last tensioner I used was too small to accommodate the geared pulleys) * pulley should...

This is a simple x-belt tensioner for the Anet A8 printer. I wanted a x-belt tensioner that fulfils following criteria: G2 geared tooth pulley should fit (the last tensioner I used was too small to accommodate the geared pulleys) pulley should be...

... have same problems like me with X axys rods and can't put them into right place (see attached pictures). ...Print Settings Printer: Anet A8 Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 mm Infill: 20 % Notes: Support only necessary in tensioner.

... bolt by 1%. 13/08/2017: v2 has a bigger 11mm opening to accommodate a 9mm teethed idler pulley wheel. These are the ones I used: http://www.ebay.com/itm/301834183849 Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 25%

An X-Belt tensioner that I made to accommodate my X-Axis guide rods that did not seat fully upon assembly. ...This part may require that you find a longer belt for your printer.

Material: Aluminum Alloy Tooth: 20 (T) Pitch: 2 (mm) Bore ∅: 5 (mm) Belt Width: 7 (mm) Overall dimensions: D18x9mm required materials for assembly M3 Hex nut: 1 pieces M3 Screw 20mm length: 1 pieces M4 Hex nut: 1 pieces M4 Screw 35mm - 40mm length: 1...

The recess in the casting is 7.6mm wide and in most X-Belt Tensioners the guides are 8mm wide. In mine they are 7.5 mm wide. The holes are 3 mm and intended for M3 nuts and bolts. Maybe it helps one or the other has the same problem. ... Sorry for...