anycubic extruder 3d models
85681 3d models found related to anycubic extruder.thingiverse
Had a lot of problems with random under extrusion, even at low speeds and high temperatures. ...Finally find out it was a weak spring, now prints perfectly. Remix is to fit for Anycubic extruder.
thingiverse
Anycubic Kossel Extruder Light....why?? why not!! 5mm LED. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jxkhsXmwuNQ
thingiverse
Simple holder for cables going from Anycubic Kossel's extruder, helps alot with their stabilization and overall cable management. Mounted with screws that are used to hold the extruder. ...09.2017 - added new version with a little thicker arms and...
myminifactory
The are a lot of extruder Parts out there for the distance problem between the Extruder wheel an the hole. ...But i could not find a adapter i can just add to the extruder without screwing new parts on.
thingiverse
The are a lot of extruder Parts out there for the distance problem between the Extruder wheel an the hole. ...But i could not find a adapter i can just add to the extruder without screwing new parts on.
cults3d
The are a lot of extruder Parts out there for the distance problem between the Extruder wheel an the hole. ...But i could not find a adapter i can just add to the extruder without screwing new parts on.
thingiverse
I've broked the fitting and didn't had the tools to the get rid of the broken gear. ...:-( During printig i held the tube with my bare hands.
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2cl6m5x7Qc1
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2cl6m5x7Qc1
thingiverse
Things for upgreate extruder anycubic kossel. ... For print tpu (flex) filament.
prusaprinters
those found on Anycubic Kossel).Also included are variants for dual and tripple extruder setups. This design is compatible with most extruder constructions. ...In particular with BMG and MK8 (Creality & Anycubic).Note: Only the dual and...
thingiverse
This is a bracket I made to get the titan extruder out from behind the Z rod. I find it a lot easier to get to now. ... Nice simple mod no need to extend the wiring if you flip the motor 180 degrees so the socket faces the printer.
thingiverse
Anycubic Kossel Extruder Upgrade for Flex Filaments
cults3d
Anycubic Chiron Extruder Threading Aid (Spare) DE Anycubic Chiron Extruder Einfädelhilfe (Ersatzteil) Wer die Einfädelhilfe vom Anycubic Chiron Extruder verloren hat, kann sich hiermit ein Ersatzteil drucken. ... EN Anycubic Chiron Extruder Threading...
thingiverse
Anycubic Chiron Extruder Threading Aid (Spare) DE Anycubic Chiron Extruder Einfädelhilfe (Ersatzteil) Wer die Einfädelhilfe vom Anycubic Chiron Extruder verloren hat, kann sich hiermit ein Ersatzteil drucken. ... EN Anycubic Chiron Extruder Threading...
thingiverse
Anycubic Prusa Extruder Cable mounting improvement Print Settings Printer: Anycubic Prusa Rafts: No Supports: No Infill: 20%
thingiverse
I was annoyed by the extruder cable of my AnyCubic Kossel Plus just dangling around. So I designed this (very simple) cable clip that holds the extruder cable and clips into the frame. I use four of them to guide the cable along the vertical frame...
thingiverse
Created this to use as a temporary spare as getting the Kobra extruder assembly is currently quite difficult without buying the entire printer. Aimed to make it 1 to 1, mostly, with the original. ...I recommend using some screw thread inserts in the...
thingiverse
Das ist ein Remix dieses Halters https://www.thingiverse.com/thing:3545008 Durch die Positionierung meiner Drucker in einem Schrank (Gehäuse) habe ich durch diesen Halter den Zugang zum Extruder beim Filament ein - und ausführen verbessert. ...
thingiverse
This is reverse-engineered spare part for Anycubic Delta 3d printer. The tightening screw of the idler wheel did slowly break the original part, causing random under extrusion. ...This part is near 1:1 replica, but I did increase thickness of that weak...
prusaprinters
... angepasst auf M4.Seitlich sind ebenfalls Bohrungen um optional mit M3 Gewindehülsen etwas anzubringen. ...Wird von mir nicht benutzt.Eine Zeichnung ist enthalten.Der Abstandhalter ist bei mir notwendig gewesen um den Originalen Extruder zu befestigen.
cults3d
i was pissed of to fiddly filament change without sight. ...so i moved my extruder to the front. printed with support on my i3 mega, speed 80mm/s. ...longer bowden needed, so i made a connector with two m6 push connect fittings.
thingiverse
i was pissed of to fiddly filament change without sight. ...so i moved my extruder to the front. printed with support on my i3 mega, speed 80mm/s. ... longer bowden needed, so i made a connector with two m6 push connect fittings.
thingiverse
Easier for manual extrution. Recommend use support and print it with the Mark at upper side for better looking . ...also you can print it with the Mark at bottom and no support needed.
myminifactory
This object was made in Tinkercad. ...https://www.tinkercad.com/things/8hf5cyFCAsu
thingiverse
I added M6 threads and cleaden it a bit, The treads were needed cause the hole for the bowden clamp was to big to thread in and it would hardly stay in
thingiverse
This is mount for extruder anycubic kossel 0-15 degrees