anycubic i3 mega camera mount 3d models
480296 3d models found related to anycubic i3 mega camera mount.pinshape
Print Settings Printer: Anycubic i3 MEGA Rafts: No Supports: No Resolution: Any Infill: 50% Older MEGA models have different (lower build plate) thickness. ...:-/ Post-Printing You will need a camera screw to fix camera to the mount. ...
thingiverse
This is a camera mount for Anycubic i3 Mega. The allows raspberry pi camera to be mounted at the right hand side z-axis carriage. It would be easier to design a mount on left hand side z-axis carriage, but the part cooling fan duct obstructs the...
cults3d
I had only tested it on the new one (December17) I discovered on my older i3 MEGA(August17) the plate below build plate where the camera mount, mounts, is slightly thinner on the older one. ...This clip thickness is 2.85mm Ill make another version to...
thingiverse
I had only tested it on the new one (December17) I discovered on my older i3 MEGA(August17) the plate below build plate where the camera mount, mounts, is slightly thinner on the older one. This clip thickness is 2.85mm Ill make another version to...
thingiverse
A single print camera mount that slips just under the build plate. I would increase the infill to make it more sturdy. Try 50% or more... No supports needed. The model should be positioned already, when you load it in to slicer. I use Cura, so...
thingiverse
This mount snaps onto the metal frame of the Anycubic i3 Mega and holds the Wyze camera off to the right or left side of the bed. The Wyze camera can then be articulated to point in the desired direction. ... UPDATE 2/11/19: Added a clip for the USB...
cults3d
This mount snaps onto the metal frame of the Anycubic i3 Mega and holds the Wyze camera off to the right or left side of the bed. The Wyze camera can then be articulated to point in the desired direction. ... UPDATE 2/11/19: Added a clip for the USB...
thingiverse
Camera mount that snaps on Anycubic Mega X printer. You can use it for mounting Raspberry Pi camera or any other accessories. Holes are 6mm in diameter. My print on Anycubic Mega X snaps on perfectly, doesn't slide down and is easy to remove. ...
thingiverse
I used this i3 mega go pro mount: https://www.myminifactory.com/object/3d-printer-camera-mount-mainly-for-anycubic-i3-mega-34849 And this c270 mount for the cr-10: https://www.thingiverse.com/thing:2281259 You might need to remove the bed from the H...
thingiverse
ANYCUBIC I3 Mega - XXL Camera Mount - BETTER VIEW :-) I Try to get a better view Point with my Camera so I remake a thing. To stream the video without shaking, a holder for the boom to make it stable. Fix the camera cable with 2 cable ties through...
thingiverse
Magnets: https://www.amazon.de/gp/product/B06X977K8L/ref=oh_aui_detailpage_o02_s01?ie=UTF8&psc=1
thingiverse
... umgestaltet. ...Geändert wurde lediglich der Montagearm für die Z Säule. Die spezifische Enderaufnahme samt Schild wurde gegen die Aufnahme des Filamentsensorhalters von BrezZZz getauscht. Somit passt die Kamerahalterung jetzt an den i3 Mega.
thingiverse
Octopi Raspberry pi 3 b+ holder for Anycubic I3 MEGA with camera mount.
thingiverse
Octopi Raspberry pi 4b holder for Anycubic I3 MEGA with camera mount ATTENTION! ...doesn't fit for Anycubic Mega X.
thingiverse
Ich habe hier eine Halterung für die Amazon Blink mini WLAN Kamera entworfen. Die Halterung wird auf der linken Seite an den 2 oberen Schrauben befestigt. ...Die Kamera kann mit dem original Kugelkopf einfach eingeklipst werden.
thingiverse
Camera mount to attach Pi Zero and camera on adjustable mount to rise with the z axis as the print continues. ... Motion software (https://sourceforge.net/projects/motion/) installed on pi to provide webstream,.
cults3d
... faster print with less support. Back of camera case didn't fit either, had to use file and knife. Therefore removed some material. Update 3/11/19 Added hole to the tilt arm for an M2 skrew to reduce the wobbling of the camera when the bed moves.
thingiverse
... print with less support. Back of camera case didn't fit either, had to use file and knife. Therefore removed some material. ### Update 3/11/19 Added hole to the tilt arm for an M2 skrew to reduce the wobbling of the camera when the bed moves.
thingiverse
The camera case sits onto a post on the pivot for easy removal (I made a second mount that is connected to my enclosure). The face plate is cut away to make removal of the camera ribbon cable possible without removing the camera from the case. The...
thingiverse
Redesigned the camera enclosure front part a bit, so that the flex cable is coming from the bottom-back instead of the top. ...This way you spare a couple of centimeters of cable :) The arm, enclosure back and the hotbed bracket are untouched.
thingiverse
This camera mount, mounts to the Z-Axis of the Anycubic I3 Mega. It works with all Cameras that have a Camera Tripod Screw Mount, such as Logitech C920. ... I would advice against mounting heavy cameras like a DSLR.
thingiverse
Designed for Anycubic I3 Mega Z-Axis Camera Mount C920/Tripod Screw by Aerocalculus https://www.thingiverse.com/thing:2858044 This item allows you to only need an Allen key to install the camera mount, while holding this from behind.
thingiverse
Correct issue in STL file Possibility rear bed mount
cults3d
Correct issue in STL file Possibility rear bed mount
thingiverse
Parts: Base + distance Case Camera mount Top holder Anycubic Mega I3 (move from base (Key G -> x-Axis) and rotate (Key R - 90)) Side holder Anycubic Mega I3 (move from base (Key G -> x-Axis) and rotate (Key R - 90)) Screwable top and back mount...
thingiverse
# Anycubic I3 Mega Raspberry Pi camera mount ---- This mount can be screwed to the Z-axis of the printer to move the camera up with the ongoing print. ... This is the [case](https://www.thingiverse.com/thing:3610624) which i used.
thingiverse
This is an **addon** that allows you to mount various compatible raspberry pi housings to your **Anycubic i3 Mega** 3D printer. It also includes a camera mount that can easily be attached to the RasPi housing. - Mainly intended for a **remote...
thingiverse
I wanted a camera mount for my Anycubic i3 mega that clipped on to the base plate, there are few nice mounts available but none that I could find that clipped on. This is based on my i3 mega so may not fit all i3 mega machines. Its fairly stable but...