anycubic kobra neo leveling 3d models

Simple screen cover for Neo

Simple guide to help keep the filament in the center of the print area over the print head on an Anycubic Kobra Neo printer.

anycubic kobra neo height gauge It's used for setting the sensor height to the nozzle height. ...Nozzle touches the lowest part and then you slide the sensor down to touch the

This is a remix of the Filament Guide from @tommytwothousand. ... It has been adapted to the Anycubic Kobra Neo, replacing the original spool holder and using the screw threads. ...

... in varying lengths and quantities as indicated in the STL file name (although the 3.875 inch version is the only one that needs four copies). If printed with the Kobra Neo, I have not found there to be any need to apply any bed adhesion settings.

ADXL345 X-Axis and Y axis mounts for the Kobra Neo There's another mount by Applepie2 but it doesn't fit the accelerometer I have which I think seems more commonly available (e.g. https://www.amazon.co.uk/dp/B09M6MSF7J).. There are screw mounts...

... I can make the change. I think the most common heatbreak sub is from the creality cr10, and that one is 27.5mm long. I'll post pictures once it's done printing. It's a "work in progress" once it's printed, mounted, and tested on the Kobra Neo.

Anycubic Kobra Go/Neo Logitech camera mount

Never lose your Anycubic adapter again with this secure stand that keeps it in place. ...Tested on Anycubic Kobra and Kobra NEO.

This is a spacer designed for the Anycubic Kobra Neo spool holder to accommodate Overture cardboard 1kg spools

This is a bracket to replace tiny plastic wire bracket on Z axis of Anycubic Kobra Neo (maybe suitable to other too). Was created to give cables more organised look. ... Printing time around 50 minutes with 30% cubic infill, PLA.

I have designed this tool holder for all of the tools included with my Anycubic Kobra Neo plus one pair of tweezers and a few memory cards. It's mounted with four M3*10 screws and V profile insert nuts. ... Designed in Solid Edge 2021 Community...

This is an LED mount for the Anycubic Kobra Neo and Go. It slots into the top bar with a friction fit and includes a filament guide. There is also a version without the filament guide for the Go. After printing, you can super glue the two pieces...

I created this in order to have a wall-mounted spool holder for my Anycubic Kobra Neo that sits under my desk. I used double-sided gorilla tape to mount it but I can add holes for screws if that is requested. It's designed to use the spool holder...

A couple of simple mounts designed to attached the new form factor Adafruit ADXL345 to an Anycubic Kobra Neo for measuring required input shaping (although this may also work with the Kobra Go and other similar printer designs). No supports are...

Simple diamond pattern Z-Axis camera mount for the Anycubic Kobra Neo. I used the Camera Mount for Logitech C270 on 2020 Extrusion by NikNolte on Thingiverse: https://www.thingiverse.com/thing:2426231 as reference for creating the base brackets...

... ...when I first bought the Kobra Neo, i noticed the loom droops and even touches the bed during the first layers. this should provide enough support to get it out of the way. should not need it to be angled upwards. ... will require 2 small zip ties

I grabbed the idea to have a trash tub outside of the built plate underneath the place where the Anycubic Kobra Neo (my new printer) dumps its filament trash when loading a filament or purging the nozzle at the start of the print. I printed...

Watch here: https://www.thingiverse.com/thing:5894002 Composed these feet from the Kobra Go Foot Block https://www.thingiverse.com/thing:5817375 and the Higher Feet Vibration Dampening https://www.thingiverse.com/thing:5566982 . You need to print...

When you buy a dual z axis kit, a lot of times they are Ender-specific and include t-nuts that you cant use because the anycubic version is different. Just print this out and use it to mount your stepper! Requires at least 2 M3 screws (ideally 4 for...

... "feet"), it should snap into place on the rail and will even slide a bit so you can adjust the position. I believe this will work for both Anycubic Kobra Neo AND Go printers, and theoretically any printer with rails matching the above measurements.

Original posting: This is a remix of combination of Vap3Lif3_MCMXCV fan duct that was designed using https://www.printables.com/model/378928-anycubic-kobra-neo-fan-duct by Martin. ...The circular fan duct was found on the internet (no idea where I got...

This is a remix of an upgraded fan duct i found on printables, https://www.printables.com/model/378928-anycubic-kobra-neo-fan-duct. The endoscope camera that i used can be found on amazon,...

Les fichiers STL sont téléchargeables ici : [DOSSIER COMPLET](https://cults3d.com/fr/mod%C3%A8le-3d/outil/guide-axe-z-avec-molette-pour-anycubic-kobra-neo "DOSSIER COMPLET") Il est recommandé d'imprimer ce modèle avec une imprimante 3D réglée et...

Print 2 and place them on both sides with the bed centered on them and the print head between them Bring the gantry down to rest on the flat top of the tools Loosen the bed and the gantry connections Tighten in order Bed Rollers Gantry...

I got the end off a model I found somewhere but can't remember where. (Sorry) Since I wanted to run a PTFE tube from my Sunlu dryer to the printer, I made this adapter. It uses the M10 size threaded adapter. I feed the tube all the way through...

This piece fits in the tracks under where the nozzle defaults to. This will catch bits that fall off the nozzle and keep them from going under the printer. ... Supports - Yes (I used Tree supports with the bottom on the bed) Infill - 10-20% Layer...

Print two sets of shortest rails for the back

Kobra STL updated on 05/06/2023 You can Set any STL as a Background in Cura: you can watch this Tutorial in German on YouTube: https://www.youtube.com/watch?v=9B_IlDR205I Path: D:\UltiMaker Cura 5.3.1\share\cura\resources\definitions\...

This is a remix to mount the articulated arm on an Ancubic Kobra Neo