ar15 thumbhole stock 3d models
40036 3d models found related to ar15 thumbhole stock.thingiverse
A1-length thumbhole buttstock for AR-15 and Airsoft M4 gas blowback (GBB) rifles. Universal fit for rifle, commercial carbine, and mil-spec carbine buffer tubes. For installation on rifle buffer tubes, an upper buttplate screw is required and...
grabcad
RIFLE STOCK DESIGN WITH THUMBHOLE. INLET FOR REMINGTON MODEL 700. ...INLETTING NOT 100% COMPLETE.
thingiverse
This is an attachment for the Nerf Raider to convert the stock to a thumbhole version with space for a 1500mah 3s lipo. If you don't use the stock to house a battery there is no modification required to the raider stock. ... Will require 6 4-40 .75...
thingiverse
A remix of koobysnacks77's HERA CQB furniture. ... This was modified by Jay Battle to be more accurate to the fitting of an AR15. ... I just uploaded it for him.
thingiverse
Thanks for taking a look, here's a quick summary of the stock :D Why use the stock ? - BIGGER battery tray - Looks cool Notes: Last updated 26th April - Lay all parts flat on the build plate. Battery cover shld be printed at a 45 degree...
thingiverse
Remixed the battery cover on the stock to support magnets so it snaps into place and you dont have to unscrew it to remove the battery. Also changed the filet to a chamfer cause it matches the rifles vibe better imo. ... See screenshot for print...
thingiverse
It fits a standard Ar15 buffer tube, you might have to scale it by a percent or two for that perfect fit, I have included a sliced part of the stock so you can test fit.I used the old bolt, spring and nut from my original stock. Hatchbox bronze PLA...
thingiverse
It fits a standard Ar15 buffer tube, you might have to scale it by a percent or two for that perfect fit, I have included a sliced part of the stock so you can test fit.I used the old bolt, spring and nut from my original stock. ...Edit 4/6/17 Added...
cults3d
Here you can print a rear stock in AR15 style for your Alligator 2 crossbow. When unfolded, this can be clamped under the Axel. This can then be reloaded directly when shooting with a magazine without having to set down the crossbow. The best way to...
thingiverse
https://www.facebook.com/3DprintedAirsoft I was asked to make these so why not to share them, one adapter is for buffer tubes with thread and one is with ris rail for stock from sig etc. ... It require stock mount only 10mm height, you may need to cut.
cults3d
Reinstall your stock/brace and bam you can instantly extend your stock/brace to the same place every time without issue. -These files are for PERSONAL USE ONLY. They are not to be reproduced and sold. Intellectual property belongs solely to...
thingiverse
this was done on an ender 5+ this was printed standing upright ( butt plate down ) this stock was designed just for something to prove I could do it and work as a functional stock, works with standard lower and buffer tube as long as square at the...
thingiverse
You might need to elongate the grip screw hole in the stock for proper fit. UPDATED 12/21/2018: Fill 1mm gap forward of grip, relocated selector spring hole and grip screw, added ambi selector lever cutouts, and narrowed grip mount. Please post a...
thingiverse
Thumbhole Stock for the Lynx, I used M3 hardware where needed in the replaced parts.
thingiverse
So I really liked the idea that HappyCatFilms had however I wanted to adapt it for a thumbhole stock as well as make it full length and add a sling stud. The idea with a bag rider is that when using a rear bag, it helps the bag stabilize and...
thingiverse
This is a thumb holed version of the recon stock I've uploaded earlier I've printed it out this time lol I've split it into 5 parts with 2 connectors the connector will need a little bit of sanding before connecting it because I didn't accounted for...
cults3d
... a model of a minimalist airsoft stock. The stock fits the ar15 replicas. For full operation, you need: - m3 20mm screws - m3 nuts - a spring cut 7mm from the pen Kolba waży 40 gram i jest bardzo wygodna. ...Idealna dla ludzi robiących lekkie sety
cults3d
Key for stock tube M4/AR15. If you like it, you can find my other creations here : https://cults3d.com/fr/utilisateurs/AT_Eleven_3D/cr%C3%A9ations My facebook page: https://www.facebook.com/ATEleven3D Unless otherwise stated, all creations...
cults3d
The following model is an adapter to install a M4/ar15 stock tube on a Jing gong sa58. It might be compatible with other fixed stock fal/sa58 like the classic army or other but I never tried. The adapter is screwed instead of the original fixed...
thingiverse
Modeled this in preparation to modify it to move the battery into the stock. Nothing special, just an exact copy of the stock that comes with the gun. ... In addition to the STL file, I also uploaded the native SolidWorks 2018, STEP, and IGES files...
thingiverse
Re-designed Mil-spec stock from Grabcad. Can fit big batterys. Work-in progess, but useable as it is. ... Thank you if you support my work.
thingiverse
... BUILD THIS ! Code : HA3D-016 Model : Hornet_Standard_Stock Designer : Hornet Test done with Tianse PLA and TPU. ... FOLLOW THIS PROJECT AND MANY OTHERS IN "HORNET AIRSOFT" YOUTUBE CHANNEL : https://www.youtube.com/channel/UCjG2fck4nwnPs5ap3ZqGF_w
thingiverse
FYI i printed AR15-main_stock.STL You can then print the latch AR15-stock_latch.STL If you want you can print AR15-stock_swivel.STL and AR15-stock_swivel_screw.STL for some more eye candy. However i haven't printed these yet and it's unlikely they...
thingiverse
Ruger 10/22 ar style stock. ...Uses ar15 collapsible butt and pistol grip. 11" to 14.5" lop (length of pull). ...Finer threads for a tighter fit.
thingiverse
The standard ar15 buffer tube dimensions were used except the threading. the tube was canted 10 degrees down. No known issued yet. It has not been printed and tested for fit yet. ... Find the latest updated version here...
thingiverse
A small and simple device you can use on your buffer tube to limit the stock's travel.
cults3d
... move around his tube? ...Her come a small shim who reduce the clearance for your tube stock The part is too thick or too thin for your stock? The file is not STL but STep, so you can easily change the thickness. ...(Default thickness 1mm) Cheers
cults3d
Stock adapter for the AAP-01 OEM stock to allow you to use a M4 buffer tube and stock. You will need the following hardware: M5x 15 and M5x25 machine screws. Also added a shorter version of the adapter. Upto you which one you run with Remove the...