armattan badger dji 3d models

Simple Armattan Badger DJI & TBS Antenna Mounts Use a razor blade to open the slits to allow the MMCX connector to fit through the mount. Look at the STL to see where the slits are. ...Immortal Ts have slits also.

The Armattan Badger DJI Edition frame does not actually need any extra parts, but as I always slather my builds with TPU, mostly to give some personality, here are the parts I designed for my Badger to accommodate the DJI gear.

The Armattan Badger is one of my favorite frames. ...The original camera cage does not fit the DJI O3 very well, so I made this.

Its a Remix from 4569504 for the Badger DJI Version

Armattan Marmotte Badger DJI SMA

Badger DJI with Immortal T Not perfect, but it works

DJI Air Unit mount for the Armattan Badger. ~8g printed at 30% infill. 4 perimeters. It's designed to pass the 12 gauge battery wires underneath the air unit. Antenna mount clamps down a bit on the cable. You can put heat shrink on the cable if...

These 2 parts hold the DJI Air Unit itself in the frame. You only need the bottom because the top plate keeps it from coming out. ...The print in TPU is tight enough that it does not move even in a crash.

DJI FPV Air Unit stock antenna mount for Armattan Marmotte/Badger DJI version.

... - they should also fit for the Armattan Badger. ... Further I made a remix of the great "Armattan Marmotte/Badger DJI FPV antenna mount by onderko123" design. ...I've added a GPS Module mount for the TBS M8 and the TBS Immortal T antenna.

I made 2 mounts, one for GoPro Session 5 and and one for GoPro Hero 8, for my Armattan Marmotte (https://rotorbuilds.com/build/26420) - they should also fit for the Armattan Badger. Further I made a remix of the great "Armattan Marmotte/Badger DJI...

I needed to add an M8Q-5883 GPS to my badger, so this is remix just adding on a gps slot onto another antenna design (original can be found in remix section). Printed vertically with supports on angles greater than 76 degrees. ...You'll likely need...

Minor remix of Bomba_fpv's design to fit the Armattan Badger DJI edition frame. It extends the base to cover and wrap around the four arm nuts. I also removed the bits that needed screws through to the aluminium tail standoffs as I feel that weakens...

I decided to try my hand at creating a new design for my DJI Badger and Marmotte quads. This is what I came up with so far. 3-21-21 - Redesigned antenna holder. ...

Models included: Badger-Marmotte Unibody DJI Vista Heavy Badger-Marmotte Unibody DJI Vista Lite As an extra: BN-180 GPS Mount BN-220 GPS Mount Not sure if you can print it, I can print it for you. ...Just write me bopiloot@hotmail.com or Find me on...

Armattan Badger HD Bottom plate for DJI FPV Air Unit and motor wires protector

Armattan Badger HD Bottom plate for DJI FPV Air Unit and motor wires protector

This is a redesign of my DJI Badger and Marmotte antenna mount https://www.thingiverse.com/thing:4740625 and includes a GPS mount. ... 3-21-21 - Updated model to make easier insertion of antennas.

I made a remix of the awesome "Armattan Marmotte/Badger DJI FPV antenna mount" to make it fit to my TBS M8.2 which is just a little bit larger than the TBS M8 version. ... Link to the original antenna mount: https://rotorbuilds.com/build/26420 Link...

I remixed this from two designs on Thingiverse. ...It combines the side by side antenna design of Onderko123 and the Immortal T Mount from Swivaljaw's design

A simple mount for the Armattan Badger or Marmotte to support the air unit antennas and optionally a SAM-M8Q 5883 GPS module.

... storage. ... Use 2 zip ties through the hole (1mm) and secure the tbs crossfire antenna. Fit stock DJI O3 antenna, Caddx vista antenna. HGLRC LHCP Long Range Antenna, RunCam O3 Air Unit fpv antenna. ...Any Antenna with 4mm fit BN220 and BN180 GPS

This cam mount is perfect if you can not tighten the screews of the top plate any more into the titanium cage. But it will also works with not "damaged" cages :-) Print with PLA and 100% infill + Support. ...Printing orientation is best with the...

2 little holders for an immortal T to be mounted across the gap between the arms on the Armattan Badger DJI Edition frame. ... The holes closest to the back screw use 10mm screws into the stand offs as usual and the others go into the back of the...

A remix to include the Crossfire mount. For best results and minimum support, print as shown in the picture + support. Infill 30%. ...

Models included: Badger-Marmotte Unibody CRSF Vista Heavy Badger-Marmotte Unibody CRSF Vista Lite As an extra: BN-180 GPS Mount BN-220 GPS Mount Not sure if you can print it, I can print it for you. ...Just write me bopiloot@hotmail.com or Find me on...

Fits DJI Action2 with magnetic Cover.

x2 needed to go over stand offs and crimp between bottom and top plate

Some parts, i designed to my Armattan Marmotte build: - Motor wire protector/motor soft mount - DJI cam spacer - Vista antenna/Immortal-T mount - 10mm capacitor mount Parts that are not My design on yhe pics: Cam cage bumper (bottom plate):...