armattan japalura 4 3d models
538911 3d models found related to armattan japalura 4.thingiverse
I design this support for my japalura 4". ...I glue it on the frame.
thingiverse
This thing is perfect with this thing : https://www.thingiverse.com/thing:2210169
thingiverse
Simple adapter to allow the use of micro cameras in the 4" Armattan Japalura frame. I've included the STL and the Fusion360 file if you want to tweak it for your use. The length will just barely keep the camera behind the roll cage so it should be...
prusaprinters
Simple adapter to allow the use of micro cameras in the 4" Armattan Japalura frame. I've included the STL and the Fusion360 file if you want to tweak it for your use. The length will just barely keep the camera behind the roll cage so it should be...
thingiverse
Canopy for Armattan Japalura. Saves about 10-12 grams over stock setup. Mount for 22mm camera (I had an old Caddx cam...) and a SMA. There are recesses for M2 nuts on the inside. Slightly lonnger bolts than original is needed. ...
thingiverse
This is a Buzzer holder for the Japalura 3" it should also fit the 4". The buzzer that I have is 9.5mm. ...I designed this in Fusion360 I also included the .step file so you can mod it for the buzzer that you have.
thingiverse
The 4 inch Armattan Japalura is still one of my favorite quads, I recently did a complete rebuild and drew up a few parts. This is a mount for the TBS Crossfire Immortal T antenna that is designed to be printed in TPU with supports in the center area...
thingiverse
Immortal T and insta360 go mount for the armattan japalura print as its shown in tpu. ...I printed it at 100% infill so it was solid and i had no jello in my video
thingiverse
The 4 inch Armattan Japalura is still one of my favorite quads, I recently did a complete rebuild and drew up a few parts. This is a BN-220 GPS mount that is designed to be printed in TPU with supports and the top of the mount facing the bed. To...
thingiverse
Just the mirrored part to Alros's Japalura runcam swift. ...
thingiverse
Japalura is designed to fit 3-hole full size cams, print this mount if you want to safely accomodate micro size cams. It's not symmetrical to allow access to cam screw when inside a kwad. Printed with devil design tpu. ... fusion360 model file:...
thingiverse
Armattan Japalura Motor / Arm Guards with skid pad.
thingiverse
Whoop style prop guards for the Armattan Japalura frame. ...Printed and it all fits perfectly.
thingiverse
Print with TPU, i made it for 4mm base plate found here: https://armattanproductions.com/pages/product_details/17858 It should also fit default 3mm ones.
thingiverse
Takes M3 Screws, Fits on the Back of the Japalura And Mounts an Axii Uxii or a Lollipop Print in TPU
thingiverse
This little adapter plate will let you stack a Shark Byte TX5R.1 on top of a 30x30 FC/ESC stack on an Armattan Japalura. I'm presuming it will work on some other builds as well. The VTX is a tight fit in the Japalura frame, but it all works out...
thingiverse
This is a combination of the top mounted battery pad and lollipop antenna holder.
thingiverse
japalura 168mm motor 1407 props 3" This frame is a test frame,similar in appearance to amattan japalura, which rides between 3 and 4 inches,this frame is TRUE X no is like japalura armattan Supports 30mm and 20mm flight controller sizes As well as...
thingiverse
Feet for the Gecko 4 to match prop guards. This will fit zip ties up to 2.5 mm wide. ... Prop Guard can be found here https://www.thingiverse.com/thing:4729831
thingiverse
... a bit of foot room for another component. I used some stand-offs to secure it. More pictures on [my post](https://flyingsquirrel.ch/adding-a-runcam-split-s-4-to-an-armattan-gecko-frame/) on adding a Runcam Split S 4 to an Armattan Gecko frame. ...
thingiverse
This is a prop duct for the Armatta Gecko 4. Duct was measured for 90MM props. ...Looking for Gecko 3 Fan duct can be found here https://www.thingiverse.com/thing:4943111.
thingiverse
... UPDATES; 5-4-2020 beta frame 6-4-2020 The holes have been roughly modified to better match the pieces, The design of the covers and frame have been polished. motors 1407 3650kv Enjoy it ,,, and if you have any support ... ...tell me.
thingiverse
I made this personally for my Armattan Chameleon Ti using my Gopro Hero 3 and Gopro Hero 4. If you have the waterproof cover for Gopro, unscrew the lens cover and put it inside the case. ... *reuploaded
thingiverse
This is a lightweight yet durable Armattan Marmotte TPU Mount for the GoPro session 4/5. It makes it easy to remove the GoPro, but it holds it very well. It weighs approx 15 grams at 26% infill. See print settings and Post Print Photos Below. ...
thingiverse
Simple tail mount for Foxeer Lollypop 4+ on an armattan Chameleon or Chameleon TI Updated V2 removes some excess material to allow for better airflow over components and a little sleeker look. Left V1 for anyone preferring to cover the space in...