astrox switch 3d models
67548 3d models found related to astrox switch.thingiverse
This is a support I made for my astroX switch. Already tested once, looks really nice but needs more testing. ... Infill: 50% Made in ABS
thingiverse
I deigned this parts to revamp my AstroX switch. I did't like the idea to use a GoPro mount as "turtle fin" and the models around are just too big while i just need something like this. ... Requires an M3x20 screw I design a new model for the...
thingiverse
This is as close to a copy of the AstroX Switch top plate as I could get. I scanned it in and tried my best to get all the measurements right, etc. The top plate is a curvy beast so I had to eyeball some lines with splines, but it matches up pretty...
thingiverse
This GoPro Session Case is designed to fit the AstroX Switch Top Plate 35 or 45 degree mounts. ...
thingiverse
sma antenna mount for the astro x switch frame. ... print in tpu, no supports, 40-50% infill this is a remix of a few other mounts that i have continued to modify to fit different frames.
thingiverse
gopro session 5 mount for astrox switch link for download : https://cults3d.com/fr/mod%C3%A8le-3d/divers/gopro-session-5-mount-astrox-switch
thingiverse
AstroX Switch top plate Session mount. Standard 35* camera angle. ... Add the wedge if you want 45*
thingiverse
AstroX Switch 45degree Center Top Plate mount. Zip Tie hole in the center for added security on the top plate. The small supports inside the strap slot are only there for printing. They will disintegrate during the print. ... Any remnants can be cut...
thingiverse
Canopy for astro X swith frame. ...Micro camera, axii and cap mount.
cults3d
Gopro session 5 mount Astrox switch short version
thingiverse
Gopro session 5 mount short version for astrox switch link for download :https://cults3d.com/fr/mod%C3%A8le-3d/divers/gopro-session-5-mount-astrox-switch-short-version
cults3d
These are arm covers for the FPVDirect SonicX. ...It'll fit twisted motor wire, e.g., if you're using a 4-in-1 ESC. They should also fit the AstroX Switch. ... There is also a version in which the ImmersionRC Tramp TNR can slot in and be secured.
cults3d
This is a wedge-style GoPro Session mount for the AstroX Switch series. The mount sits at a 30deg angle and is intended to sit on top of the carbon top plate. ...The GoPro is secured with a battery strap with some foam/velcro underneath.
thingiverse
These are arm covers for the FPVDirect SonicX. ...It'll fit twisted motor wire, e.g., if you're using a 4-in-1 ESC. They should also fit the AstroX Switch. ... There is also a version in which the ImmersionRC Tramp TNR can slot in and be secured.
thingiverse
This is a wedge-style GoPro Session mount for the AstroX Switch series. The mount sits at a 30deg angle and is intended to sit on top of the carbon top plate. ...The GoPro is secured with a battery strap with some foam/velcro underneath.
thingiverse
A mount so you can secure a capacitor at the rear of the baseplate. ... There are files for the following: - Panasonic Low ESR 1000uF 35v (12.5x20) - Panasonic Low ESR 2200uF 35v (16x31.5)
thingiverse
Final design of the Session Case with additional securing back strap and FOV adjustments after testing
thingiverse
Holes added (enlarged) for M3 screws for the TBS SMA (or RP-SMA) antenna mount. ...Also added material for slots to the top so that it can be zip tied to the CF top plate which will keep the mount from dropping down the posts.
thingiverse
This is a remix that combines two wonderful designs, I wanted to have a support for lollipop antenna and for dual receiver antennas in the same support. ... There are two designes one with antenas that face down & other ones that face up.
thingiverse
Remixed by request. Have not confirmed fit. Best printed in TPU. ...
thingiverse
Created this mount to be able to use the Foxeer XAT600M on this frame, it should also work for other cameras with same size. ... The file has both sides to print at the same time, it should be printed in flexible filament as it has a tight fit.
thingiverse
10* wedge to add if you want to increase the camera angle to 45 degrees.
prusaprinters
<p>Created this mount to be able to use the Foxeer XAT600M on this frame, it should also work for other cameras with same size.</p> <p>The file has both sides to print at the same time, it should be printed in flexible filament as it has a tight...
thingiverse
Revised this Arm End Protector to not only be a soft motor mount, but also add Motor Protection
thingiverse
There is a opening to run a zip tie through the middle to secure it solidly to the top plate in the center. There are also 3 very thin supports that are only for printing where your velcro camera strap runs under the camera mount. These only help...