atn x sight ii hd 3 14x 3d models
991353 3d models found related to atn x sight ii hd 3 14x.thingiverse
This is an external battery kit for the ATN X-Sight ii HD 3-14x Day/Night scope. Since the internal AA batteries will only last 2 hours or so, adding an external battery pack will significantly increase the run time. The picatinny mount is sized...
thingiverse
This is a tool for removing the protective filter in front of the X-Sight ii objective lens. ...Made this because some dust had settled on the objective behind the filter and I wanted to clean it out
thingiverse
Needed some covers for my ATN X-Sight-4K HD scope to protect it from scratshes and what not. ...It's a loseish fit so that you can glue a microfiber cloth on the inside so minimize scratches.
cgtrader
|| ATN X-Sight II HD 5-20X ||
thingiverse
A mockup of my ATN x-sight 4K 3-14, for testing things and stuff.
prusaprinters
A mockup of my ATN x-sight 4K 3-14, for testing things and stuff. Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 0,32 Infill: 15% Filament: 3DE PLA white Notes: I cut it in half in my slicer and print it...
thingiverse
ATN USB port cover. Others existed but I wanted it threaded like the original. at 100% print size it threads well and snugly. You may have to advance it back and forth a few times when you are first installing it. Ridges added to the outside so you...
prusaprinters
ATN USB port cover. Others existed but I wanted it threaded like the original. at 100% print size it threads well and snugly. You may have to advance it back and forth a few times when you are first installing it. ...Ridges added to the outside so you...
thingiverse
Made this for a friends ATN X-Sight night vision scope cover. You will need a paper clip or piece of wire about .040" to connect the three pieces. The holes are tight so you will have to drive the pins in. Go slow when driving in the pins. You do...
thingiverse
Made a knob to help with difficult to grip and hard to move focus knob. ...If printed at the right size it should be a snug press fit.
thingiverse
cap to cover usb/sd/hdmi ports. ... I use TPU as its flexible like rubber.
thingiverse
This is a lens cover for the ATN X-Sight 1 3x12. It screws into the sunshade that comes with the sight. It has a full cover, a 1/2 inch hole for day use and a full open for night use. ...Print Settings Printer: Prusa I3 Acrylic...
thingiverse
Lens caps for ATN X Sight 4K. May also work on ATN Thor 4 but hasn't been tested. The objective lens is for 64mm bell The ocular lens is for 54mm bell. Print base out of TPU and lid out of PETG. The hinge pin is a piece of PETG. If needed...
thingiverse
This is a mount for the Anker 20100 battery to the ATN X-Sight. The mount1 files have a clamp that also has a mount for the IR light. ...Print Settings Printer: Prusia I3 ...
thingiverse
Night and day difference :) . ... Adjust to center position so throw is from ~10 to 2. Slip on fit and tighten til snug. Hardware used: M3 x 10mm M3 Nut
thingiverse
ATN X-sight s are thirsty for power so used a PNY powerpack in case I run out of battery life, taping it to the side was not an option anymore, using the IR torch tied to the Picatinny was in need for a change so made a frame for both. Clicks snug...
thingiverse
This is a cap for the usb port while the usb cable is attached. It can be printed from pla or ninjaflex. ...Print Settings Printer: Prusa I3 Acrylic ...
thingiverse
The covers are a modification of wordblind! In addition, the front cover has a hole. The cover can be left on the scope when the sun is shining. It sometimes works better in strong sunlight than without it! The ABL cover is a modification of...
thingiverse
Work in progress. ... Has not yet been printed and tested. 68mm protective cap for X-SIGHT II as requested by thingiverse user "Franks55".
thingiverse
Use any Flexible Filament like Ninja Flex Print Settings Printer Brand: RepRap Printer: Prusa i3 8 ...
grabcad
ATN Focus Knob for X Site 2 hope it helps. 4.2mm Holes in side to tap for M5 thread and grub screws. It was a tight fit on mine so you may not need. ...Made on 3D printer
thingiverse
Eyepiece for the ATN Binox 4K... At night animal will see backlight reflections from Binox alongside the eyes. I first printed in PLA which is no problem to print. But the material is uncomfortably to wear in facecontact so I tried Ninjaflex....
thingiverse
Mount for a GoPro 3+, fits on Emax Babyhawk II HD. I soldered wires directly to the battery pins of the GoPro and connect them to +5V and GND on the flight controller, which works perfectly. GoPro 3+ w/o battery weighs in at about 45g, which is...
thingiverse
3.5" propeller guards for EMAX BabyHawk II HD quadcopter drone. ...
thingiverse
EQ mount sighting tube for the Dwarf II smart telescope. ...Can be clamped on either side of the unit.
thingiverse
This sight is divided in two simple pieces, the body and the rail, i did it like that, because, its a 3d printed component, I mean, if you drop your blaster and hits the floor with the sight, you will probably snap it out braking the rail. So then,...