atomrc flex 3d models

Flex

FLEX

FLEX

flex on the stalk

This is an example of using the flex feature

Flex is an informal seating solution for a child or young person.   I imagined it being used in casual situations like watch TV or playing console games. While the basic cross section gives the chair flexibility all the waves and contours make the...

GoPro Mount for ATOMRC AUK FPV Drone

AtomRC Swordfish Vista mount. Done with the left heel. ...Do not judge strictly.

A mount for the gopro hero 4 to fit the atomrc dolphin

AtomRC Dolphin esc plate. ...Print with no top layers or bottom layers to use your infill as ventilation

Some of the parts I used in my AtomRC Dolphin build, as seen here https://youtu.be/_WoeBPlrSDc

I have made smaller fins for the atomRC Swordfish. ...As a reference, I took the annotations from Andrew Newton's video https://youtu.be/DLr22CuZqJc

Aerodynamic and torque resistant motor mount for the Atomrc Dolphin. No support required. ...A regular motor mount plate and 4 M3x30 screws required

Replacement for the wooden base plate in the rear compartment of AtomRC Dolphin with two 30.5x30.5mm mounting places. I've printed using PETG. ...Fusion360 model included.

the origilan plywood plate is not needed here. https://www.prusaprinters.org/prints/77219-landinggear-atomrc-killer-whale Print Settings Printer Brand: Prusa Printer: i3 MK3 MMU 2Rafts: No Supports: YesResolution: 0.2 Infill: 20% Filament: PLA...

Canopy for AtomRC Dolphin plane Designed in 2 parts top and bottom for supportless print I personally eSUN LW-PLA with 3% infill, 2 bottom layers Contains a hole for the DJI Vista antenna.

Reference scans from AtomRC Dolphin. Note that the front canopy has been modified to maximise airflow through the front section of the aircraft. ... Produced by https://www.thingiverse.com/brogers123/designs using Einscan SE scanner by...

This is the AtomRC Dolphin vertical stabilizer For the Left stabilizer just mirror it in Cura. ... Designed for LW-PLA with infill 0% - total weight 9g PLA version will be around 20g+

Front Landing Ski for the AtomRC killer whale. Made after several versions the top is made to meet with a servo + horn. It is reinforced as to not break in the cold. ... Please print with supports PRINT AT 75% SIZE

Rear landing skis made for the AtomRC KillerWhale. Tested in the snow and improved upon to this version. Reinforced to not snap in the cold. ... Please print at 100% size and with supports

I got a AtomRC dolphin with a 1700kv ES2306 motor with a german 7042 prop. I put this values into ecalc and figured out, that on 4S the temperature of the ESC could rise to an unhealthy level. ...So I designed this air inlet for the ESC.

This is a "replacement" canopy for AtomRC Swordfish. This is just plain canopy with no mounts or something. It has enough clearance for 4s 21700. This model is not meant to be printed, rather, use it as a baseline for your own mods. Add your own...

Hello everybody, I design some parts for AtomRC Dolphin. Flying with a single camera mount https://www.youtube.com/watch?v=0Q9CI8qhfBU Nose parts: Install the holder in the foam, I used 3 screws to join the nose with the holder. ...

... stress on the servo. But you can also just use steel push rods. the whole from wheel assembly then gets glued in the spot. the origilan plywood plate is not needed here. https://www.prusaprinters.org/prints/77803-landinggear-atomrc-killer-whale

Atomrc Dolphin elevonThree different types:Plane elevon,  you need to glue in servo horn andduct tape elevon to main part of the wingplane elevon with place for connectors to the wing (use 16mmx28mm)With place for horns and connectors (see...

AtomRC Dolphin dji action2 nose

Blank for the AtomRC Dolphin GoPro Nose.

matek Pitot tube mount for atomrc dolphin

Caddx Polar mount for AtomRC Dolphin RC plane. ...May fit other 19mm wide cameras as well.

An air inlet for cooling your vtx inside of a depron model. ...I am using this for a AtomRC dolphin. ... I made the duct a bit longer so you can cut it to suit your purpose.