beer bottle holder 3d models
364354 3d models found related to beer bottle holder.myminifactory
Solve the problem of bottles crowding your fridge space and rolling around on the shelves with this new hanging bottle holder! There's often extra room at the top of the fridge - Make use of that dead space by hanging your beer bottles from the...
thingiverse
Handy little beer holder for the fridge. ... Print 2x beer holder & 3 x beer holder leg Takes 6x small screws (around 20mm 4g)
thingiverse
... ... I created two versions for standard german beer bottles, one for 0.33l (up to 62mm diameter) and one for 0.5l (up to 70mm diameter). ... Caution: The holder might slide down but if you add a bit of rough tape to your crutch it works pretty well.
thingiverse
'Cause of an accident I have to wear an abduction splint the next seven weeks. ...A long time not having one hand free while drinking a beer. So I created this bottle holder which is mounted on the splint with a 20mm wide velcro strap. ...Cheers!
thingiverse
Here's a simple stubbie holder designed for ~330ml beer bottles with a diameter of about 60mm. Height is about 110mm. Use as low fill as your printer is capable of to increase the insulation properties of the stubbie holder. I found my felix had...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=57679 Instructions Using the following options: bottle_space_width = 75 dualstrusion_mix = mixed primary_color = white secondary_color = white pairs = 2 spacing = 2 strip_thickness = 3 tolerance...
grabcad
Human shaped beer or soda holder/balancer drinking a beer bottle. ...If you have any questions please email me at Sarkis@dal.caLinkedin: https://www.linkedin.com/in/georges-sarkis-7a5544100/
thingiverse
basiclly i took this to print for my lad to put on the side of his bed frame work found out it wont fit a beer bottle but just about fits his baby bottle so i added a hook and scaled it up a bit so it would fit a beer bottle or can i printed this...
thingiverse
Or you add another 2x3 row, giving you 17 bottle capacity (plus five on top = 23 bottles, almost a full case of beer) I measured some beer bottles I had on hand, and this design should fit most modern "slim and tall" bottles. It also works for 0.5...
prusaprinters
<p>I like the original design but it didn't fit my pegboard. I need to print it again because the bottom didn't print correctly. ... I think that I may need to rotate the design when printing in order to get a solid bottom.</p>
thingiverse
Based in: https://www.thingiverse.com/thing:3479795 Lasercut (3mm)
thingiverse
adjust model in slicer to: Z = - 0.1 support at 65°
prusaprinters
I have created a holder for standard beer bottles (70mm diameter) that can be mounted to the shaft of an umbrella (38mm diameter) I have added a 80mm version for bigger umbrellas, but it's untested.
thingiverse
With this item you can stack 5 beer bottles (0.5L) in your fridge. ... Note: original thing is for 0.33 bottles, this remix is for 0.5 bottles.
thingiverse
This is a 50cl bottle holder for the fridge. It can be used alone or connected in series for better holding a number of bottles. It may work for wine bottles and 33cl bottles too, but I took as a reference a 50cl bottle and haven't tried it yet with...
thingiverse
https://www.thingiverse.com/thing:4760105 i just don't drink beer out of cans, and it was too large to be printed on my ender 3 pro. so i designed it to fit 0,5L bottles, divided it to 8 parts, and added the handle and lids separately. the lids...
thingiverse
Here we have a simple bottle holding clip which allows you to secure bottle to a rope. This give you the ability to tie your bottles to your kayaks etc to allow them to be cooled in the water as you paddle. ... Many thanks
thingiverse
Updated model to scale, slightly reinforced it. ...There are minor issues with bottom layer (it`s not perfectly flat).
thingiverse
I created this beer bottle mounted cigar holder at the request of a friend. Simply snaps around the body of the beer bottle, giving a convenient place to hold your cigar. It also lays flat, so it works on the table top as well. Described from...
thingiverse
This turns an empty Beer bottle into a pretty candle holder Instructions The File has a simple line, BUT Load your beer bottle into your lasercutter with the butt to the y axis, I have a 50Watt Epilog helix and for raster 50% speed and 100% power...
thingiverse
This bottle/can holder is edited to secure against something with 4 normal screws. ... Remix from: ZenoxDemin Edited by : KoekMaker98
cults3d
This is my bottle/can holder. Can be printed without support but has quite a bit of bridging. You can scale down the Z axis. ...This will make it easier to pull cans out.
thingiverse
This is my bottle/can holder. Can be printed without support but has quite a bit of bridging. You can scale down the Z axis. ...This will make it easier to pull cans out.
thingiverse
Printed to fit 0,33 bottles in the two lower rows and 0,5 bottles in the upper row. Enjoy! ... Printed with the same settings as the original.
prusaprinters
... (5mm thick, 18.5mm diameter). I gave a couple beers to a friend using this, with the intention that he'll send it back with two beers for me to try out. ...I added our names so I don't get it mixed up with other ones I make in the future.</p>
prusaprinters
A new model for transport was added as well.Makes and comments are appreciated.Different Models:Bierflaschenhalter: tall 0,33 L bottles with 60 mm diameterBierflaschenhalter stubby: short 0,33 L bottles with 70 mm diameterBierflaschenhalter 0,5 L...
thingiverse
I also added more connection point so not only you can connect the holder in series but you can also put different rows in parallel to hold the bottle from two points instead of one, making it possible to stack the bottles on top of each other to...
thingiverse
I wanted to make a nice box for the local beer i bought as gift for friends. ... It's lasercut with a K40 laser out of 3 mm mdf. If you are wondering which beer it is you can find more information on the site; http://www.belgoobeer.be/
prusaprinters
<p>divided it to 8 parts, handle and lids separately.</p><p>the lids are a little loose, so they might come off too easily. i recommend glueing them on, or making a remix. i might upload a better version of them</p><p>things to print:</p><p>2x...