belt clamp 3d models
79610 3d models found related to belt clamp.grabcad
The corner braces for belt clamp systems. ...They are designed for assembling picture frames, drawers, chair frames or other articles of various sizes and configurations prior to glueing or fixing.
thingiverse
This is a belt clamp for RepRap less than standard. This is a part of my Y carriage for RepRap. ...Look here http://www.thingiverse.com/thing:779890 If you need this model with nuts holder look here http://www.thingiverse.com/thing:779919
cults3d
Wonderful design by LiViS! ... I wish I had found these months ago. I noticed on my Flying Bear they were close to the bottom belt so I didn't want them to rub. ... I radiased the corners to prevent them from touching.
thingiverse
Wonderful design by LiViS! ... I wish I had found these months ago. I noticed on my Flying Bear they were close to the bottom belt so I didn't want them to rub. ... I radiased the corners to prevent them from touching.
grabcad
To provide the conveyor belt clamping during the service conveyor system.
thingiverse
GT2 timing belt clamp, 2mm pitch and 6-10mm wide, with 4mm mounting hole.
grabcad
Belt clamp for the ChilledPrusa, based on the RepRap Mendal Prusa V2 with a variety of modifications to increase rigidity.
thingiverse
GT2 simple belt clamp. ...Print Settings Printer: Motedis_kossel Resolution: 0.2 How I Designed This Solidworks
thingiverse
This thing is a replacement piece I designed for a belt clamp on the Pheonix 3D printer.
myminifactory
GT2 timing belt clamp, 2mm pitch for 6-10mm wide belts, with a centered 4mm mounting hole. ...Was designed for a project I had going on.
thingiverse
... fix the drive belt for both X Axis (extruder) and Y Axis (print bed). The Belt Clamp connects to: Acrylic Part 12 - Build Plate Base - https://www.thingiverse.com/thing:3339453 3DP14 - Extruder Backplate - https://www.thingiverse.com/thing:3339297
thingiverse
A small belt clamp for your own carriage designs. My belt is quite stiff and thick, so maybe it is a bit too large for bendier belts. ...Just let me know and I'll upload another version.
youmagine
Belt Clamp with integrated Tensioner for GT2 belts Thanks to JC Doll with his algorithm for generating toothed pulleys as belt clips. ...http://www.thingiverse.com/thing:117987 OpenSCAD file included for your customization
thingiverse
I found the belt clamp to be too shallow and did not grab the belt well so with a quick tweak extended the "reach" as well as tightened the tolerance between the teeth and the flat part.
thingiverse
for those living in metric countries: toothed belt clamp for metric belts t2.5 low (4mm) and standard (7mm) version holes print right for m3 screws, hole center distance 18mm, overall width 28mm
thingiverse
Remix of Belt Clamp + Tensioner for mounting underneath a print bed frame. ...Made to mount underneath the v-slot frame of my new print bed assembly, I've included both 60mm and 30mm versions.
prusaprinters
A small belt clamp for your own carriage designs. My belt is quite stiff and thick, so maybe it is a bit too large for bendier belts. ...Just let me know and I'll upload another version.</p> Category: 3D Printer Parts
thingiverse
I needed a GT2 belt clamp that could handle an outside loop, and couldn't find one, so I made this, which just slips over the side of the two belts placed back-to-back. ... I printed using PLA with 4 walls.
thingiverse
This is a belt clamp for RepRap less than standard. This is a part of my Y carriage for RepRap. ...Look here http://www.thingiverse.com/thing:779890 If you need this model without nuts holder look here http://www.thingiverse.com/thing:779917
thingiverse
This is a simple 3/16" x 1" x 1" belt clamp for and HTD3 Belt. this is the belt used for the X and Y axis belts of the OneUp and TwoUp Printers. I used these for the Y-Axis belts to prevent the belts from sliping out of the MDF clamps. ...After printing...