bike hydroflask holder 3d models

For detailed mounting instructions, go to https://www.instructables.com/id/40oz32oz-Hydroflask-Bike-Bottle-Cage/ PETG or ABS/ASA is probably best, especially if you plan on printing it in a dark filament, as those two materials have higher...

For detailed mounting instructions, go to https://www.instructables.com/id/40oz32oz-Hydroflask-Bike-Bottle-Cage/ PETG or ABS/ASA is probably best, especially if you plan on printing it in a dark filament, as those two materials have higher...

... worth checking for everyone. Time will tell if Matthew's bottle holder was tall for a reason : ) But I took this for its first spin tonight and it held together great, with limited rattle even when using this small bottle. ...Happy printing : )

A hydroflask handle that you will need to scale up x10 to print. ... Print Settings Printer Brand: MakerBot Printer: ...

I wanted to carry my hydroflask but my backpack didn't have a holder, and none of the backpacks I had could carry the size. Fits like a glove. I have also used the white strap holder as seen in the picture to prevent the strap from sliding. ...

This is a extension for a cup holder to hold a 32oz Hydroflask.   There are two parts to print and you can use CA glue to join them together.   This was designed for a 2021 Ford Explorer cup holder.  The base extension reaches to the...

This multipurpose car cup holder can hold just about any kind of bottle but will specifically hold must types of Hydroflasks up to 32oz.Due to cutting out as much material as I could and and having everything at an upward angle, there will be no need...

32oz bottle holder made to slide on to desk. I put a screw through the top to hold it tight against the desk. could be improved. ...thrown together in about 3 minutes

Car cup holder insert for a Hydroflask 32oz bottle

Designed for the 40oz / 1.2L HydroFlask bottle.Measurements of the section that goes into the car's cup holder:Diameter: 7.5 cmHeight: 5.72 cm

This rediculous thing is a cup holder adapter for your 40OZ hydroflask. Be sure to measure your hydroflask before printing, as this thing takes up a LOT of TPU. I printed mine on 30% infill density and it barely fits, but it never tips over. I...

Expand your car or truck cup holder to secure a regular coffee mug or 32oz hydroflask. Center also can secure a can of Red Bull. Bottom is enclosed so the insert can be secured to the car cup holder. I used some velcro tape. Mugs that fit snuggly...

This is a holder for the larger hydroflask bottles that are 90mm at the base. This was modeled to fit in a 2015 Honda Accord, so may not be universal to other vehicles. The opening is hollow to still allow for other skinnier cups to fit (small to go...

This is designed to make a 32oz or 40oz Hydro Flask fit in the cup holder of a 2014-2021 Toyota Tundra. There is a blank one, TRD one and one with Toyota emblem. ...I would recommend printing in PETG or something that will not warp in the heat of being...

Cup Holder Adapter for 3rd Gen Toyota 4Runners. ...Specifically fits 32oz Hydroflasks. This part prints in two pieces. ...They're meant to fit tightly together.

I got tired of my Hydroflask rolling around in my truck. ...This is an addition to the stock cupholders in a 2012 Ram 1500.

Fits snugly in the cup holder with a little bit of space around the bottle, and you can put things inside if you aren't using the water bottle as it's hollow to the bottom of the cup holder. ...I added the Jeep grill cutout because it's a Jeep...

This plate was designed to quickly install in the tiny front cup holder area of the Audi Q5. It has a ridge to accommodate quart-sized water bottles or normal coffee/tea mugs. ...Note that a water bottle can still tip over with spirited...

A magnetic cup holder for older vehicles with metal floors. I'm using it in my CJ2A. It's not as strong as I would like for off-roading, but it's fine for daily driving. If you can come up with a better design to make the magnetic hold stronger,...

I wanted a custom 3d printed solution to hold the hydroflask in my car instead of printing a generic adapter that goes in the normal cup holder. This 3d print replaces the cup holder that is in the center console between the two front seats of the...

A cup holder extension/adapter for larger water bottles (32oz Hydroflask with 91 mm base) that will fit into a car cup holder (designed for Nissan Rogue center console cup holders). Will not prevent use of adjacent cup holder. ... Print upside down...

Two versions of attached here, passenger and driver. ... Originally designed to hold a Hydro flask but also modified to hold just about anything then added the phone holder. ... With the cutout for the charging cord, this works great!

Two versions of attached here, passenger and driver. ... Originally designed to hold a Hydro flask but also modified to hold just about anything then added the phone holder. ... With the cutout for the charging cord, this works great!

-conversion for wide mouth Hydroflask for car or random water bottle holder -water bottle fits snugly within print -3 different prints that need to be connected together and can be printed in different colors -for car I would print in a lighter color...

... ...Added extra material to the front the holder to no longer need a strap. You may need to sand the two long nubs inside the holder to your preferred amount of tightness between the bottle and the holder. ...Be sure to print with the flat side down.

If you are looking at this you had the same issue as me where the hydroflask didnt fit the car or trucks cup holder. I made this to fit both cars and allow for a coffee cup with a handle. This was my first design so its not the best, but not terrible...

... shown in the picture. The cupholder size is designed to fit a 32oz or 40oz Hydroflask. I used Prusaslicer and created a support enforcer just for the hook part, no other supports. ...Printed at 0.3mm with Prusament PETG.</p> Category: Automotive

This fits the 2020 6-seater seats and hooks onto the seat next to the seat belt holders as shown in the picture. The cupholder size is designed to fit a 32oz or 40oz Hydroflask. I used Prusaslicer and created a support enforcer just for the hook...

This is a cup holder insert for the center console of 2018 and newer Ford Expeditions and F150 trucks. I do not know which other vehicles it might fit. It is designed to hold a full sized Hydroflask and also has a cutout for the handle of a...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/eUYt2BtXXqt