bn 220 gps 3d models
16937 3d models found related to bn 220 gps.thingiverse
Holder for Beitan BN-220 GPS Module. Made to fit iFlight XL frames. ... Frame hole - 6,0mm Hole for gps module - 22,4mm x 20,1mm x 6,5mm Frame holes center-center distance - 21,0mm
thingiverse
I have BN-220 GPS modules at home so modified the great original STL in Tinkercad for my MicroLongRange build. You can secure the GPS with zip ties. ... BN220 GPS module US warehouse: https://fas.st/mcOn4 From China: https://fas.st/oksUXT
thingiverse
Yet another holder for the BN-220 GPS module. This design is to be used as a part of another design. JST connector is intentionally designed inside and locked otherwise it can disconnect because of vibrations. I would not recommend using any other...
thingiverse
Cover for the Cherrycraft Stamina frame to install a BN-220 GPS on the top plate.
thingiverse
This was designed to both hold the BN-220 gps puck and tidy up all the wiring going into the flight controller.
thingiverse
I didn't want to keep GPS in the fuselage near vtx's and HD-camera's radio noises nor dig it into the tail's foam. ...So made this tail surface mount for Beitian's BN-220 gps module. Print upside down without supports. ...
thingiverse
I needed a mount for GepRC Mark4 HD5 BN-220 GPS Module and couldn't find one. So, I took two great models - https://www.thingiverse.com/thing:3547332 https://www.thingiverse.com/thing:4096116 And mix them so it will fit the frame and the GPS module....
thingiverse
This is a mount for the BN-220 GPS and TBS SMA Pigtail for the Armattan Badger and Marmotte frames. I find it prints best with the box that holds the GPS facing the bed and with supports. ...It's designed to be printed in TPU.
cults3d
A simple BN-220 GPS mount which pops on the included antenna mount which comes with the Johnny FPV QAV-S special edition frame. I recommend gluing the mount or using one small zip tie on either side of the data/power connector to keep it in place...
thingiverse
A simple BN-220 GPS mount which pops on the included antenna mount which comes with the Johnny FPV QAV-S special edition frame. I recommend gluing the mount or using one small zip tie on either side of the data/power connector to keep it in place...
cults3d
BN-220 GPS mount for the Armattan Rooster or any other quad with 24mm spaced mounting holes. -Angled at 25° to get an clear view of the sky while flying home. -Raised mount to stay clear of a top mounted lipo battery. Recommended installing with...
thingiverse
Crux 35 camera and antena holder remixed with GPS frame for Beitian BN-220 GPS
thingiverse
BN-220 GPS receiver and VTX antenna mount for Geprc Mark4 frame and clones. ... Antennas angle is 25 deg.
thingiverse
Made it slightly longer in Tinkercad to fit the Diatone GTR349 and have the GPS and cable stay out of the way of the capacitor and power cable. Printed in TPU. Used doublesided tape to fix the GPS to the mount. It's 2 gram, printed without supports...
thingiverse
I found that placing GPS right below the VTX antenna have an impact on finding satellites so I decided to put it on the side. ...And placed like this, it is more protected during a crash Right and left version availables
thingiverse
Mount for Beitian BN-220 GPS for Volantex Ranger tail boom. Place gps module with wire plug pointing to the tail to prevent accident detaching. ...
thingiverse
Side GPS support for [Beitian BN-220 GPS](https://www.banggood.com/custlink/mmvRFtRw1f) You will need the following to mount it correctly - 1x small zip tie - 2x M3x6 nylon screw - 2x M3 nylon nut
thingiverse
BN-220 GPS module battery strap mount. - Fits straps up to 2cm width and 3mm height - Designed to be printed in <b>TPU</b> Enjoy your flight! ... <br> My things: https://www.thingiverse.com/r__/designs
thingiverse
BN 220 GPS mount for TBS Source One Frame. Mounts to the tops of the frame above the FPV camera as I do not plan to use a Gopro on my quad. ...
thingiverse
BN-220 GPS receiver and VTX antenna mount for iFlight XL5 (old) frame and clones. Antennas angle is 30 deg. With and without holes for TBS Immortal antenna. ... For 5 mm uprights.
thingiverse
(You can get this GPS module from https://www.banggood.com/Dual-BN-220-GPS-GLONASS-Antenna-Module-TTL-Level-RC-Drone-Airplane-p-1208588.html?cur_warehouse=USA) If you are looking for a GPS mount for BN-180 GPS Module, use this one...
thingiverse
FPV drone case for Beitian BN-220 GPS for top battery place. Fix it with the two same battery straps. ... If you want fix cable on the case you can make two hole and put a cable tie (see picture for details)
thingiverse
This PETG mount moves the GPS module 5mm farther away from the VTX, and is sized to fit the Beitian BN-220 GPS module. NOTE!!: The plug for the factory Flywoo GPS module will fit into the BN-220, but the positive and negative pin positions need to be...
thingiverse
Mount for [Beitian BN-220 GPS](https://www.banggood.com/Dual-BN-220-NEO-M8N-GPS-GLONASS-Antenna-Module-Ublox-M8030-TTL-Level-p-1208588.html?p=MW151810738534201705&cur_warehouse=CN) module to use with quads. Easy mount to battery strap or zip tied...
thingiverse
THIS HOLDS my bn-220 gps module to the top of my drone's battery using the battery strap as a holder. the mount is very tight and is hard to get the gps inside but once there it will not fall out and will actually be very difficult to remove and...