bosch bit holder 3d models

Hex bit holder for blue Bosch drills that has a hex insert hole just above the battery. The holder has slots for 8x2mm magnets. It was made to fit my Bosch GSR 1800, but will most likely fit other drills that have hex insert slot. It is a snug and...

Hex bit holder for blue Bosch drills that has a hex insert hole just above the battery. The holder has slots for 8x2mm magnets. ...It was made to fit my Bosch GSR 1800, but will most likely fit other drills that have hex insert slot. It is a snug and...

This is a remix to fix two issues. ...First, I decided to use 10mm x 5mm magnets to give more holding power for the bits. Secondly, I opened up the bit holes a little to make the bits go in and out easier.

A small shelf for BOSCH bit set in a case (100mm x 46mm)

Customized version of https://www.thingiverse.com/thing:3440818 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3440818

I liked the [Bit-Holder for cordless screwdriver (Bosch)](https://www.thingiverse.com/thing:4512868) and had used it for several month, until eventually it broke recently as it has a weak spot at the right arm. As anyway the original was way too...

This holder can store 20 1/4" bits. Designed to be printed with 2x0.4 mm walls without infill, top and bottom layers. This gives the holder some flexibility, as the black part of my IXO body seems to be an elliptic conoid. ...SketchUp model is attached...

Держатель бит в новые боксы Pick and Click L и M от Bosch

This is a 1/4" hex bit holder. ...It's compatible with the ones used in some Bosch drill bit sets.

Remix of the Holder to fit Bosch Expert Spade Bits 16-32mm

Bit Halter für die Wabenstriktur von Bosch oder Sortimo Boxen

Enlarged and moved the pin for a good fit with this Bosch device. ... Very useful to have multiple bits in a convenient location.

Bit holder for the Theo Klein Bosch cordless drill.

I didn't like the stock bit holder so I took it apart and made an adapter for any bit holder. ... I personally prefer the Wera rapidaptor.

Ersatz Bithalter für den Bosch GSR 12-20 HX Benötigt werden 4 Stück Rundmagnete mit 8 mm Durchmesser und 2mm Höhe Replacement bit holder for the Bosch GSR 12-20 HX You will need 4 round magnets with a diameter of 8 mm and a height of 2 mm

Bosch 10.8 V bit holder (Drill body / circle radius ~50mm) Hold 2 hexagonal bits (6.3 mm or 1/4") and one round bit (6mm) I have glued it with double side glue (M3 VHB) 10.7.2018 - I have added a Triple Hex holder, as Tedder asked View Tedder's...

This is a magnetic bit holder for Bosch drills. I have an GSB 18V. But may fit on others too. I used what i have. So there are 3pcs 3x18mm and 4pcs 3x8 magnets inside. I made also a file for 11pcs 3x8. Its better to print it in high resolution.

Also I did some minor size adjustments to remove small gaps and to give it a tight, non-moving fit.Finally added a bottom layer to stop bits getting pushed out of the back side when the row is removed from the storage box. FYI I used the Bosch...

Material: Pla Size: 82mm x 20,29mm x 13,20 mm Filament needed: 8,62g Print time with my printer: 22m12s Supports: no

I printed this piece with Flex

Bosch GSR 10,8-2Li bit holder Otomar

My Design for a simple bit holder for my Bosch GDR 12v-110.

I made a holder for my Bosch electric Screwdriver and bits. ... im waiting for magnets, im intended to insert magnets on the bottem so the bits stay in place when i take the holder with me to another room.

Updated as there were printing issues. ... I have printed this and use it daily. This is a side mounted bit holder for a Bosch (or other) Router Table. ... Does not require supports.

Bosch pick and click container do not sell these holders without bits. ...And the ones you get with bits only work with borsch impact bits.  Print with support and PETG for best fit. 

Change the size of the Bit holder (1/4" or 6,35mm diameter) depending on your printer. Kywoo Tycoon settings I've used with Cura: PLA+. 210°C 0,1mm layer thickness No infill Adhesion activated When using Cura, mind activating ironing with...

Holder for additional long or short bits for Bosch IXO to keep them in the box at an angle.Originally in this place is an opening for manual.To install my design the lip around the opening must be cut and depending on fit somtimes the holder must be...

Holder for additional long bits for Bosch IXO to keep them in the box at an angle. Originally in this place is an opening for manual. To install my design the lip around the opening must be cut and depending on fit somtimes the holder must be...

________________________________________________________________________ A simple design for a bit holder in the lid for Sortimo / Bosch L-Boxxes. The holder consists of two parts and can hold 26 bits. The holder is attached via the holes in the...

My Design for a simple bit holder for my Bosch GDR 12v-110. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 0 % Filament: Sunlu PLA+ Grey Notes: Cura Settings: Wall Thickness: 1.2 mm...