boscoyo studios 3d models
88975 3d models found related to boscoyo studios.thingiverse
Used for your Boscoyo Studios Lollipop Sticks. This is to be mounted to the bottom and top of the lollipop stick to give it support and so you can mount it to emt. For use on 1/2" EMT. Align holes and zip tie to your stick. ...
thingiverse
These use a 14.5" long piece of 1/2" sch 40 pvc and slides inside the small sphere from Boscoyo. ... The bottom piece then slides onto 1/2" galvanized pipe.
prusaprinters
<p>Needed a way to hang the Snowflake on my porch. Wanted a way to have a built in support for a cable/rope as well.</p> <p>Simple design, just works.</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p...
thingiverse
Needed a way to hang the Snowflake on my porch. Wanted a way to have a built in support for a cable/rope as well. ... Simple design, just works.
cults3d
Pixel pushing jig to assist with pushing RGB pixels into the ChromaTrim V4 from Boscoyo Studios Print it vertically as shown in the image for maximum strength and not needing any supports. I set the walls to have 4 perimeters and 25% infill. ... It's...
thingiverse
Pixel pushing jig to assist with pushing RGB pixels into the [ChromaTrim V4 from Boscoyo Studios](https://boscoyostudio.com/product/chromatrim-v4/?attribute_pa_color=black) Print it vertically as shown in the image for maximum strength and not...
thingiverse
A design to mount Boscoyo Studio 16-inch snowflakes. This allows mounting the snowflake on a 1-inch schedule 40 PVC pipe (USA spec). The mount uses a 1/4-inch bolt passed through the pipe, the back-mounting block, the snowflake with the front block,...
thingiverse
Simple singe screw mount for Boscoyo strips. The clip is deep and wide enough to support bullet and square pixels. This was designed to screw into a 1x2 for eave mounting. Added a v7 update. ... It it a little rounder, and just a little smaller to...
prusaprinters
Simple singe screw mount for Boscoyo strips. The clip is deep and wide enough to support bullet and square pixels. This was designed to screw into a 1x2 for eave mounting.</p> <p>Added a v7 update. ...It it a little rounder, and just a little smaller to...
thingiverse
Designed these holder to work with 1/2" PVC to hang the Boscoyo 24" Snow Flakes. The 3 prong is the only one that is directional one point on the holder is not rounded same as he prop. Foe the Two prong snow flake I have 3 designs depending on type...
thingiverse
Have not tested with the original 8' long boscoyo strips, have not tested with other vender strips. The side of the pixel will sit right at the bottom of the eave. Works with 2" or greater spacing.. 09-19-2020 - Added a clip for a 2.5" wide...
thingiverse
Have not tested with the original 8' long boscoyo strips, as of 08-20-21 - been tested with Holiday Coro strips and works. The side of the pixel will sit right at the bottom of the eave. Works with 2" or greater spacing.. 09-19-2020 - Added a...
thingiverse
Mount for the new boscoyo ice queen snowflake. Uses 1/2 pvc and zip ties, no drilling into the coro. ... Use 1/2 thumb screws to secure the pvc as well as zip ties Need 2 of them
thingiverse
This disk is designed to fit into the tube without the white insert provided by Boscoyo to limit light bleeding from one eye to the other. You will have to cut the white insert in half to cover each eye after inserting the disk. ... The Boscoyo Spooky...
cults3d
This disk is designed to fit into the tube without the white insert provided by Boscoyo to limit light bleeding from one eye to the other. You will have to cut the white insert in half to cover each eye after inserting the disk. ... The Boscoyo Spooky...
thingiverse
Boscoyo Coro Minitree base mount. Includes 4 points to stake down minitree. Ring is approximately 11.9 inches wide, but broken into 4 pieces for smaller workarea printers. Parts are numbered and joined together by dovetail joins. Using my Prusa I...
thingiverse
... hole I'm just using tension to hold them. I may eventually add a screw, hot glue, or double sided tape if the wind blows these too much. Also, if the Boscoyo strip comes out you can put zip ties around the outside to squeeze the arms together.
thingiverse
These are fasteners for the Boscoyo PixaBulb Strips when used for a MegaTree. The front side clamps around the strip and the backside locks a hook into the other side so you can hang the strip from an eye hook. The bottom is made to fasten the same...
thingiverse
Here is a set of clips to fit the Boscoyo pixel strips. The metal ones James sells are approximately the shape and size as the MSIRSingle in this collection. The single and dual ones are designed to have the strip fold over and back on itself. The...
thingiverse
Customized version of https://www.thingiverse.com/thing:3094095 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3094095
thingiverse
Pixel Cradle for Boscoyo ChromaTrim V1. ... Print on end - standing up to avoid supports.
thingiverse
This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/fLrZTks1hnQ I made to mount a lot of WS2811 on the Boscoyo straps!!! ... I love it.
thingiverse
This is for the the Boscoyo 36 Inch Chroma star. Designed to add support using the 1/2" channel. I use a 4 way connector to go between them. ...Will add pics later in the week.
thingiverse
After pushing over 150 pixels in a Boscoyo snowflake, I realized I made a mistake on the pixel order and they all needed to be removed. This design removes pixels from Boscoyo 10mm thick coro products. Place over the pixel and push until flush with...
thingiverse
This add 24 mounting points for Boscoyo strips to the base of the 12-pointed star. The original idea was to mount this on a Tomato cage. That didn't work - the Tomato cage collapsed under the tension of the strips. ...So will probably modify this to...
thingiverse
This is a base for the Boscoyo ChromaTree Glow Series. It can replace the one that comes with the Tree. ...Print Settings Printer Brand: RepRap ...
thingiverse
After finding many mounts inferior, I designed this center mount for the Boscoyo 3 prong 16" Snowflake prop. It's a tight fit into the center for the snowflake but holds it tightly. It attaches to 1/2" Schedule 40 PVC pip with 2 zip ties. ... For...