calibrate anet a8 3d models

Calibration set 180x210

... settings that you believe work better, please share! Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2 Infill: 0% Notes: Don't print this too fast. ...Printed at 60 mm/s machine setting which resulted in 9 mm/s (s3d) gcode.

this is the ultimate calibration test to check that all parameters are set correctly, it is suitable for any printer.

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Fits on a Anet A8

Good day. ...I have solved the problem of setting the same X axis height when calibrating my printer. This is my solution. ...I hope it will make it easier for you to work.

Use this tool to calibrate your Z-stepper motors. Print 2 of them, one for each motor.They are 65mm high so should be no problem clearing the z-stop switch. ...

http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: Indent = 2 TemperatureIncrement = 5 machine = Anet A8 / Anet 3D EmbossHeight = 0.5 TowerHeight = 110 BottomTemperature = 220 HeightIncrement =...

http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: BottomTemperature = 230 EmbossHeight = 0.5 TemperatureIncrement = 5 HeightIncrement = 10 Indent = 2 TowerHeight = 95 TowerSide = 20 machine =...

This is another yet calibration bed.

... from the CR-10 one by dilopsus all credit goes to him. ... https://www.thingiverse.com/thing:2856545 I just resized this to fit on my Anet A8 printer since I couldn't find one for it and I thought it would help others if I uploaded it back on here.

... the CR-10 one by dilopsus all credit goes to him. ... https://www.thingiverse.com/thing:2856545 I just resized this to fit on my Anet A8 printer since I couldn't find one for it and I thought it would help others if I uploaded it back on here. ...

When in home position measure distance from bottom of x- motor mount to nema17 stepper motor mount,then use tinkercad or other and adjust height of Z- calibration tool to suit your printer.When printed slide over your idler 8mm smooth rod.Too easy.

... to the same height. This tool isn't specific to the Anet A8 printer. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: .2 Infill: 50% Notes: Infil probably won't matter much. ... It's small enough that it's going to be pretty solid.

... a bit is fine - picture 2) If it's to high, you will see the filament not sticking to the bed. No brim, raft, rift! No infill! Turned out to be a pretty good testing methode. Print Settings Printer: Anet A8 Rafts: No Supports: No Resolution: 0.2

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: Indent = 2 TemperatureIncrement = 5 machine = Anet A8 / Kaiserlich PLA TowerHeight = 100 EmbossHeight = 0.5 BottomTemperature = 230...

http://www.thingiverse.com/apps/customizer/run?thing_id=1298948 Instructions Using the following options: EmbossHeight = 0.5 machine = Anet A8 / Herz PLA BottomTemperature = 230 TowerHeight = 110 HeightIncrement = 10 TowerSide = 20...

Support to Hot Bed calibration

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Customized version of http://www.thingiverse.com/thing:915435 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915435 Instructions Using the following options:...

Customized version of http://www.thingiverse.com/thing:1298948 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Customized version of http://www.thingiverse.com/thing:915435 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915435 Instructions Using the following options: Labels...

Customized version of http://www.thingiverse.com/thing:915435 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915435 Instructions Using the following options:...

Customized version of https://www.thingiverse.com/thing:1298948 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1298948

Remix of (http://www.thingiverse.com/thing:1776429) by Meermeneer

Customized version of http://www.thingiverse.com/thing:915435 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=915435 I customized this for use with filament by 3Dmonet on Amazon ...

Customized version of https://www.thingiverse.com/thing:2280529 If you want to get instructions howto manage bed calibration click here: http://www.cazda.com/en_US/3d-printer-bed-center-calibration/

Customized version of https://www.thingiverse.com/thing:2280529 If you want to get instructions howto manage bed calibration click here: http://www.cazda.com/en_US/3d-printer-bed-center-calibration/