cat5 cable guy 3d models
121040 3d models found related to cat5 cable guy.thingiverse
Cat5 Cable clip. ...Use drywall anchor to mount to wall or directly to wood.
thingiverse
This is a wall clip for routing CAT5 network cables mounted with a thumb tack/push pin.
thingiverse
... tape. For better cable fit for Cat6 and Cat5 separately. It is advisable to use ABS or PETG filament, the PLA breaks easily. The v2 files are the modified versions. ...A little reinforced at the bottom of the clip, which was a bit fragile.
thingiverse
and specifically it is set up to be used for CAT5 cable (this one wont fit CAT6 but im working on one for that) however it should be OK to use for ANY 5mm Diameter cable so long as its round. also please note due to how i designed this theres a...
thingiverse
Print this out, slip the male end of a CAT5 cable into the square hole with the cable itself slipping through the side, slide the cable down, and place a padlock of your choice through the small hole at the top. Very useful for shutting down...
cults3d
... labeling tape. For better cable fit for Cat6 and Cat5 separately. It is advisable to use ABS or PETG filament, the PLA breaks easily. The v2 files are the modified versions. ...A little reinforced at the bottom of the clip, which was a bit fragile.
thingiverse
I've provided my two STLs for wall-mountable, cable management for Cat5 cables. One was for my 5 port switch, and the other for my Draytek Router. The router (v2) has 4 cables at 15mm centres and a 40mm centre to the 5th. The switch (v1) model has 5...
thingiverse
A collections of cable organization combs. Slit dom med hälsan, as we say in Sweden. ...:)
thingiverse
Why buy a whole box of these if you only need a handful? ...They print in few minutes and you can color-match your cables.
thingiverse
I ran some ethernet cable in the basement and needed some simple cable clamps to tidy things up. These are what I printed. The first batch peeled up on the ends and so I added a single layer flat pad to hold them down. These pads break off easily...
thingiverse
I needed a cable holder that held 4 cables. So I added another spot from desktoplathes design. ... (I also have 2 and 7 slot holders on my profile) Print Settings Printer: XYZ Davinci 1.0 ...
thingiverse
I needed a cable holder that held 7 cables. So I added some more spots from desktoplathes design. ...(I also have 2 and 4 slot holders on my profile)
thingiverse
I needed a cable holder that held 2 cables. So I removed a spot from desktoplathes design. updated to my V1.2 that looks nicer. ...(I also have 4 and 7 slot holders on my profile) Print Settings Printer: XYZ Davinci 1.0 ...
thingiverse
90o bend need to be printed @ 30o angle. ...do not print lying flat as it will be weak and break when you pop the cables in
thingiverse
(TR) Ağ kablosu için delmeden çivi çakmadan kablo tutucu / düzenleyici. ... (EN) Cable holder for Cat5 network cable.
thingiverse
Clip for running a single Ethernet CAT5 cable and a power cord for a router. ... Dimensions: Screw hole: 4mm dia Large clip: 5~6mm Small clip: 2,4mm parallel cord
thingiverse
I like flat cat5 cables for when I travel. They save a lot of space over conventional cables. And I have a couple from some D-Link IP cameras that are "free" since i used other cables for those cameras. On our last trip I thought there has to be a...
thingiverse
It is sized for the plugs I used and the cable I had on hand. I printed it standing up, so as to minimize the supports, they snap right off. ... Lid was printed on it's side.
prusaprinters
<p>Small clip that allows 5 wires to be guided on a 1.5" pole with an external groove so the clip itself can be zip tied to the pole for extra security. ...Helps stop cables from swinging in the wind.no supports needed
thingiverse
Clips for standard cat5 cable. Made to fit Gorilla brand mounting tape (1in width). Cut tape to the width of the flat side of the tape. ... Cable should pop right into the clip with a small amount of force.
thingiverse
I took ChArlie's design and increased the size to accommodate 7mm wide Cat5 cable, then sliced the design in half to make it single sided and also give a flat space for double-sided tape to be applied. I put tape every third comb on the wall, 2"...
thingiverse
5mm channel dual wire clip for cat5 or similar wire. printed on Prussia i3 copy. PLA - @ 205 c Bed-@ 60 C @ 20% infill 1 gram filament -each vertical tensile holding strength - 20 lbs vertical shear holding strength - 10 lbs Shear...
thingiverse
Quick 3 cable clamp \ tie down for cat 5-6 cables. Handy for CNC's and printers that use network cable for stepper leads. I used on my MPCNC. Typical cable width I used this for was 6 to 6.5mm diameter. The holes to mount fit #8 screws pretty well.
thingiverse
Customized version of https://www.thingiverse.com/thing:457550 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=457550
thingiverse
Customized version of https://www.thingiverse.com/thing:2121248 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2121248