cateye bike mount 3d models
366025 3d models found related to cateye bike mount.thingiverse
Handlebar mount for Cateye Velo 8 CC-VL800 bike computer. Secures with M5 cap head screws. Designed for 22mm diameter handlebar. ... The two small holes in the mounting plate are for small brass "pins' that I will make to mate with the electrical...
prusaprinters
A rear bike light mount specifically for the Cateye rear lights (specific models below) to mount horizontally under an Ergon QuickClick supported saddle. Ultralight and sturdy!DetailsWeight: ~8grams at 100% infill of PETG (11g w/ screw)Fixed mount...
cults3d
FOLLOW ME ON INSTAGRAM: PB023_3d Bike mount for the torch cateue volt. ... 2 models for diferent diameters_ 20-22 cm and 30-32 cm
thingiverse
Since the installation of spurcycle bell on my brompton, i found the brompton bell redundant. ...Hence i created this bell mount to be able to hold my Cateye Wireless Computer.
thingiverse
I have a couple of older Cateye wireless bike computers that didn't come with stem mounts. I saw a couple of models on this site that were close but wouldn't fit. mread's frame mount for the Strada seem the closest. The Strada's mount (and most...
thingiverse
... a Topeak Explorer MTX rack. ...Will probably work for other CatEye rear lights, as they appear to use the same mounting system. ... The light clicks into place on the bracket and holds well during rides, but can easily be removed when parking the bike.
thingiverse
Allows you to use the Supernova Airstream bicycle light with a CatEye H24 handlebar mount. You will also need the plate that is usually screwed on a Cateye Lamp using H24 mount (the left thing in picture nr.5). You can get both together for about EUR...
thingiverse
This thing allows the mounting of a JVC Adixxion to a CatEye handlebar bike mount.
thingiverse
CATEYE bike computer mount stub for modding the LG Nexus 4 phone case by Zodd http://www.thingiverse.com/make:37263 into a bike mount. ... Instructions Printed in Makerware on High setting in ABS: 50%...
cults3d
... (buyed in 1999). ...Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. As bonus I added reinforcing ring for my bike rearview mirror - is mounted over the original fastening.
thingiverse
... (buyed in 1999). ... Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. As bonus I added reinforcing ring for my bike rearview mirror - is mounted over the original fastening.
myminifactory
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999).Screw is moved to front unlike the original.Designed in two hours, in third hour it was printed :-)Mounted, tested, is OK.As bonus I added reinforcing ring for my bike rearview...
thingiverse
A bracket for mounting a CATEYE bicycle light. ... Zip ties can be used for fixing on a handlebar.
prusaprinters
New holder for my old Cateye Enduro 2 bike computer (buyed in 1999). Screw is moved to front unlike the original. Designed in two hours, in third hour it was printed :-) Mounted, tested, is OK. As bonus I added reinforcing ring for my bike rearview...
thingiverse
A mount for attaching Cateye wireless bike computers (specifically the Cateye Padrone+) to Bontrager Blendr mounts. ...
thingiverse
This is a replacement screw for CATEYE bike lights like the GVOLT80.
prusaprinters
<p>I printed this model out of PLA with a 0.2 mm nozzle. ...A 0.4 mm might have done the job too.</p><p>The part fits great, it is very similar to the original. It might also fit other cateye products.
thingiverse
Your bicycle got stolen..? ... With the mounts for your lights..? Here is the solution. Instructions No support should be needed, mounting holes are M5, and should be tapped before mounting.
thingiverse
This is a mount for a Cateye Padrone bike computer. I wanted to take advantage of a barfly mount so i made this to integrate with some of the garmin barfly mounts here. I cut the garmin mount out and added the Padrone mount. The Padrone is odd in...
thingiverse
CatEye Volt GoPro Mount. Tested with single LED Volt 350, 800 and 1700 models. Yes, they are 2 separate mounts. Yes, they can be in 1. I made the single LED mount first and didn't feel like re-drawing that. ...Reality and physics prevent attaching 2...
thingiverse
This is a mount for the Cateye Padrone cycling computer for the Trek Blendr mount. The Blendr mount came with my Verve 3 trek bike. The mount that comes with the computer is snapped into this printed piece (grey piece in the photos). It’s a very...
thingiverse
... the camera to a bicycle handlebar. This will replace the part of the Cateye handlebar mount(http://www.amazon.com/dp/B002L2CC88) 自転車のハンドルバーにカメラとかGarminを取り付ける為のパーツです。 三種類あります。 それぞれCateyeのライト用ブラケット(http://amzn.to/1UX9Vll) のライト取り付け部分を取り替えて使います。
thingiverse
This thing allows to mount the Cateye mount in reverse direction pointing the fastener from away rather than towards the biker. ...It has been created for the HL-EL135 model.
thingiverse
CatEye GVolt50 front light fixture that attaches to Garmin out-front mount. Wanted to clear up cockpit and quickly designed this fixture that attaches to Garmin mount. Strong enough for road cycling, but light shakes a bit when going over uneven...
thingiverse
Useful spare bracket for these bike lights. Strap it to your handlebars with a couple of thin cable tyes and put a piece of rubber(e.g. from an innertube) between the bracket and the handle bars to stop it slipping. You may need to file it a bit to...
thingiverse
I wanted a better way to mount my Outdoor Tech Buckshot 2.0 speaker, so I made this. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2zV4v4OEKIB
thingiverse
Got a Lezyne bike light. ...Would like to mount on the Cateye bracket.
thingiverse
Another little part for my new Trek Madone 9 bike to mount my Cateye light directly onto the rear mount provided by Trek. ...I took the Trek bracket part from the remix and created the Cateye part from scratch on Tinkercad.