cetus3d
200 3d models found related to cetus3d.grabcad
More robust extruder drive housing replacement part for Cetus3D printers.
grabcad
Cetus3D Spool Holder with two Ball Bearing Shielded, Trade No. ...6002-2Z, for 15 mm Shaft Diameter.
thingiverse
Cetus3D Spool Holder with two Ball Bearing Shielded, Trade No. ...6002-2Z, for 15 mm Shaft Diameter OD is 32mm.
thingiverse
This part replaces the extruder cover on the Cetus3D with a version that provides a clip for the PTFE tube on the Palette+.
thingiverse
... cutter to attach it to the side of a Cetus3D extruder. ...I tapped the existing holes in the extruder to M4, but you could probably use nuts on the inside too. N.B. This is for an original kickstarted Cetus3D, not sure if it will fit the newer models
thingiverse
This is a suction nozzle for the Cetus3D fitting on Zimpure vacuum and air filter. Second iteration. ... Can be assembled with 2 m3 screws on the side of the extruder motor.
thingiverse
The Cetus3D Mk.II printer extruder drive housing installed on the printer from the factory appears to be poorly manufactured. ...This new design is more robust to replace the current part.
thingiverse
This is a model of the Cetus3D MK II printer made as a 3d-reference for designing an enclosure. The model was made in rhino so i recommend using the 3dm format. ...I've also exported some more formats so feel free to try them as well.
thingiverse
... this part the cable at the top end of the z axis can not move out of the profile. ...Use this part at your own risk. You could break the part where it should fit into. Print Settings Printer: Cetus3D Rafts: Yes Supports: No Resolution: 0.1 Infill: 99%
thingiverse
Print Settings Printer: Cetus3D Rafts: Yes Supports: Yes Resolution: .3mm Infill: ~15% Notes: I've uploaded the STL files to reflect the orientation that I printed with. My priority was making sure the screw worked, so my orientation prints the screw...
thingiverse
i have 2 version - i use the nurmal version (printed in PLA with 99% infill) the second one (slim) i dident test now - it may be enough but i like to get secure and use the thicker one :) if you try the slim version, let me know what you think :)...
thingiverse
... right on the nozzle. Right now the probe end has a little offset from the nozzle center, will fix in the next version. Here is the video of the calibration process: https://www.youtube.com/watch?v=xSNAQ_KHWec Check my other things for cetus3d
thingiverse
This is a redesigned X-Axis end cap for the Cetus3D printers. ...It is more robust than the original.
thingiverse
With this accessory you can eliminate part or all of the air blowing on the piece, especially useful with abs
thingiverse
Made this suspension system for the CETUS 3d printer because I felt left out seeing suspension systems on other printers. 8) Fits Standard Racquetballs and has a recess for the board mounting screws on the back of the main plate. ...This version...
thingiverse
This is a redesign for the Y-Axis wire guide on the Cetus3D printers. It is installed on the Y-Axis motor. ...It is designed to hold the cable for the Y-Axis motor.
thingiverse
Replacement duct for Upgarde Nozzle V2 Cetus3D MK3 Ist a remake with: https://www.thingiverse.com/thing:3383260 and original Cetus3D Duct STL (Cetus Fan Shroud with Wind Door) : https://www.cetus3d.com/product/cetus-fan-shroud-with-wind-door/ Use a...
thingiverse
... directly into the extruder. ...Designed in 123D, with built in supports, prints in one piece flat on the bed. Nozzle: 0.4mm Print time: 58 mins Print Settings Printer: Cetus3D Rafts: No Supports: No Resolution: 0.2 Infill: 20% Notes: Built in supports.
thingiverse
Just a simple Nozzel and Tool holder for the Cetus3D Printer holds up to 4 Nozzels of 0.2mm, 0.4mm and 0.6mm (or 12 Nozzels of any size :) ) Printed with the Cetus at 0.2mm Layer middel Infill - Normal Quality Have fun :) Print Settings Printer:...
thingiverse
An ode to Redonix76's Cetus3D simple Zaxis stop but for the Cetus Mk3 Only differences are the smaller nub (5.5mm) for the new rails of the mk3 and the rounded bottom to differentiate the two models easily. ... Print settings are irrelevant, worked...
thingiverse
I used blender to separate the design into three components to facilitate printing on the Cetus3d with their software. Otherwise, it's basically impossible to remove the support material from the original, fully-enclosed design. ... I also removed the...
thingiverse
Fat Spool for Cetus3D is an adapter for the Cetus3D spool holder that attempts to minimize the rocking seen when using wider and heavier spools on smaller holders. Can also be printed without supports. If this is your first print and you want to use...
thingiverse
... me know (comments or message). I also will do such a part for the z axis motor mount. NOTE: Use at your own risk. To modify your printer could void your warranty. Print Settings Printer: Cetus3D Rafts: Yes Supports: Yes Resolution: 0.2 Infill: 99%
myminifactory
This is a cooling duct made for a Cetus3d printer that aims to improve cooling for both the areas before the hot zone and the part area below the nozzle. From what i've found this works for all nozzles included with the Cetus3d printer and should...
thingiverse
This is a cooling duct made for a Cetus3d printer that aims to improve cooling for both the areas before the hot zone and the part area below the nozzle. From what i've found this works for all nozzles included with the Cetus3d printer and should...