clamp extensions 3d models

90-Degree clamp extension

I printed the source extensions as a hopeful fix which did make it better, however I found that the provided height extensions didn't want to work well with it, so I extended the extensions height and added a more grippy surface over the original...

... ...These extensions are designed to loosely fit on and extend the clamps out and allow the shifter to be securely mounted to the desk without risking it flying off. ... V2 adds a hole to put a dab of hot glue into for a slightly more permanent fit.

These extensions are designed to loosely fit on and extend the clamps out and allow the shifter to be securely mounted to the desk without risking it flying off. V2 adds a hole to put a dab of hot glue into for a slightly more permanent fit. Print...

Desk clamp extenders for the Logitech G racing wheel (G920 / G29), complements my clamp extensions for the Driving Force Shifter https://www.thingiverse.com/thing:4285245

Desk clamp extenders for the Logitech G racing wheel (G920 / G29), complements my clamp extensions for the Driving Force Shifter https://www.printables.com/model/80428-logitech-g-driving-force-shifter-clamp-extensionsPrint SettingsPrinter...

Here is a 90-degree clamp extension for an Irwin Quick-Grip clamp. It is the perfect part for clamping miter joints without having any band clamps or using nails. You can use it for making small boxes or picture frames. I myself use it for...

Extension for the hot wheels table clamp, as my son could not get the cars to go fast enough to get round the loop. Not printed it yet so may change in the next week or two. ...

Have you lost the little feet that allows you to clamp your G29 to thin tables? ...Print this thing at 100% infill and snap it on like the original ones.

This is a clamp extension for the Rollei camera mount for tubes. It extends the fitting diameter to around 35mm. It was designed to fit my bike stem. You can use this clamp with the screws of the original part. Print on side to get the layers...

The upgraded Eclipse Yoke comes with clamp extensions to help secure your yoke to your desk or table. I took measurements with one of those and made a model that closely resembles it and can be used with the standard CH Products Flight Yoke. I set...

The problem I solved was, that my desk has a very big chamfer at the edge so the normal clamps couldn´t hold the wheel. Add some additional rubber material to avoid the extension to slip. Printing: I printed with PETG and positioned the part...

If you have alu bar with outer measurement of 19.6mm(W) x 11.75mm(H), you can try this to make an adjustable length bar! ... Just screw onto one bar on either end of the 2 bars so it becomes a clamp and end stopper as well.

If you have alu bar with outer measurement of 19.6mm(W) x 11.75mm(H), you can try this to make an adjustable length bar! ... Just screw onto one bar on either end of the 2 bars so it becomes a clamp and end stopper as well.

Yesterday I said I need something clamped on the crutches which could help me in my daily life... here it is and it made my life so easier!!! The uploaded stl is for a 19mm diameter rod. ... The openscad file need the awesome library "GoPro...

Customized version of https://www.thingiverse.com/thing:3495427 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3495427

A thicker version of https://www.thingiverse.com/thing:4703368 to fit my thin glass table.

Hollowed out version of Build_beginner's phone mount extension. ...I made it hollow because I wanted it to not take as long to print.

Holds the joint of the extensions

This is a simple extension of the vise to clamp down small things to a miter saw. ...i'm including a solidworks file.

Extensions for jaw gripper for DJI Phantom 2 drone

Angled clamps to use with angled ramps from my other thing here https://www.thingiverse.com/thing:5753450 I used normal clamp for my glass table, made a smaller version for thicker desks but I think maximum is still about 15mm for normal, about 23mm...

I modified their design to keep the contact point about the same depth as the original clamps, but maintain the nice extra depth on the clamping point so it can fit my 5/8" desk top. I suspect the extensions may help reduce any rocking on the mount,...

I designed a clip with a slot for Geeetech extension board for this mount: https://www.thingiverse.com/thing:2984898/files Also had some trouble with thin walls around holes on main part, so i thickened them a little.

Im using a lightning extension cable for connection my static mic. In order to mount it to my tripod I created this clamp. ... It's screwed onto my [Tripod Cold Shoe Adapter](https://www.thingiverse.com/thing:4979879) with two 1/4" screws.

I shoot video from above view angle. ...Use this clamp on 19mm tripod leg to connect a selfie stick with gopro mount. Very useful in windy weather. ...Easy to use.

This clamp has a slider assembly that is extendable so that on a CNC router the workpiece can be held from side where the biscuit slot is not as easily accessible. The slider assembly is NOT 3d printed, but milled from phenolic or aluminum. My...

Needed to mount an extension cable to the kitchen wall, didn't want to use adhesive, made two clamps. Screwed the two claps to the plaster wall. Printed on my Vertex 3D printer using 1,75mm PLA, 0,2mm layer height. The print took just shy of an hour...

This is a simple way to prevent USB extension cable to come loose in case you trip over it.

making things a bit neater at work for the extension cords running around the room.. ... for a 3/8" OD cord -1/2" wide x 1.04" long - hole for wood screw