cord hanger 3d models
35349 3d models found related to cord hanger.thingiverse
This is leash cord hanger. You need countersunk screw M4-12 x2 and plastic bottle with water. ... Makes it easier to remove the curl of a new leash cord.
myminifactory
If you're like me, you have an embarassment of cables that you simply *have* to keep "just in case." I mean I don't know when I'm going to need a dozen 6-foot CAT-5 cables, BUT WHAT IF I DID?This little cord hanger has helped me be organized about...
thingiverse
I created this USB cord hanger to mount either on the side of my desk or on a pegboard next to my desk. If you want a version prior to the 'holes' being grouped with the solid pieces, search for the "ungrouped" version of this design. ... This design:...
thingiverse
Cord hangers that go into the Joy-Con slots of Nintendo Switch. With the cord attached from two points on each side it's easy to hang Switch from pretty much anywhere in an angle. I'm personally using these on my bed for rather comfy gaming...
thingiverse
lock designed to prevent patio umbrella from spinning around when tilted to block the sun. designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is...
thingiverse
Handy little hanger for hoses and cords. ...I currently use it for some BX Wire but an airline or garden hose would work just as well.
thingiverse
I had a pull cord by my bedside to operate the bedroom light, but it was hard to find in the dark. ...So I designed this hanger (I like the Aum sign) and printed it in glow in the dark filement. ...It looks nice at the end of the pull cord.
thingiverse
A simple hanger for a swag lamp cord. I made it to accommodate an approximately 6mm cord, but it may work for others. My print settings were unique, in that I already had a 1mm nozzle installed, so I just used that. For most, that will not be...
thingiverse
Prusa power cord holder for holding your power cord in transit or storage. ... Layer height 0.2 or 0.15, wall line count 4, top & bottom layers 4, Infill 15-20% Pattern: Octet, Support: NO, Material: PLA
thingiverse
My father was needing something to keep his phone cord off the ground, and boom I made this.
thingiverse
I designed this to run the cord of the Tesla Mobile Connector over my garage door. ...The fastener hole is designed around a Kreg wood screw but any #8 or similar screw should work just fine.
thingiverse
Clip to keep Shore Power line off of deck. ...Made to fit snugly around 5/8" O.D. Electric cord and snap over 3/16" wire. I printed in ABS and it flexes. ...Will see what a season in the sun does to it.
thingiverse
This is a hanger for the charging cable of a Tesla Model 3. Use a soldering iron to install threaded inserts into the base plate and then screw the car shaped guard onto the face. ... I'll try to get a picture once it's printed and installed so it...
prusaprinters
My father was needing something to keep his phone cord off the ground, and boom I made this. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: TechBears PLA Black Category:...
thingiverse
Ender 3 Power Cord Holder, just something to hold your power cord when in transit, storage or when not in use for a period of time. ... Settings: Layer height 0.2 or 0.15, wall line count 4, top & bottom layers 4, Infill 15-20% Pattern: Octet, ...
pinshape
Ikea HEMMA is a unversal cord for hanging lamps from celings. It comes with these clips that I keep losing, so I modeled it for 3D printing. Here's a video tutorial of how I modeled it in Fusion 360. ...
thingiverse
A nifty little clip to store your embarrassing number of CAT5 cables, USB cables, USB-A cables, Mini USB cables, Micro USB cables, HDMI cables, DVI cables, VGA cables (just in case!), Firewire cables, & others!
thingiverse
I needed someway to hold the duette cordholders( or what ever they are called), because they would fly around if it's windy. So i measured them and made some simple holders which i stick to the wall with stickypads. The dimenions of the...
thingiverse
A hanging lamp bracket for mounting from a shelf or overhanging edge. ...Pretty sturdy, but I have not tested the max load capacity with anything over 3kg.
thingiverse
This is a recreation of the cord hanger that comes with IKEA HEMMA and SEKOND pendant lamp cord sets. ...Print Settings Infill: 100%
thingiverse
_____________________________ This is a clip, fits most normal size cords. If you throw something like a household wire this will not work, only really supports wires like usb's and such that you will find around your computer. ...Also needs some...
thingiverse
This simple gadget allows you to hot-glue or epoxy the outlet end of an extension cord into it so that it can be hung using a picture hanger or nail in the wall. Instructions Using a regular US lightweight extension cord, hot-glue or epoxy it into...
thingiverse
I printed at 50% infill and my 50 foot cord is putting a good amount of pressure on the brackets and bending them, so I would advise to do around 75% infill or even 100, but you can get away with 50% as long as you're careful not to wrap the cords...
thingiverse
The Cord Cobra is a heavy duty extension cord tie that stays with your cord whether the cord is in use or hanging up. It simply uses (1) one foot piece of 550 Cord and (2) 3D printed pieces. When your cord is being used, simply wrap the Cord Cobra...
pinshape
SummaryThe Cord Cobra is a heavy duty extension cord tie that stays with your cord whether the cord is in use or hanging up. It simply uses (1) one foot piece of 550 Cord and (2) 3D printed pieces. When your cord is being used, simply wrap the Cord...
thingiverse
This is a clip I put together to hang my Christmas light extension cords along the soffit of my roof line.
thingiverse
This is a generic cable holder/wall hook to store a power cable from an electronic device (like a dust buster) while the device is in use. To attach to wall, use a removable adhesive strip like a 3m command mini strip. This holder is sized for a 1.5"...
thingiverse
These clips mount to the monitor and I use them to hang the air hoses and power/data cables out of the way.