craftsman 113 table saw arbor 3d models

Craftsman 113 10" Table Saw Top

This is a replacement for the outer belt guard (part 824359) for a Craftsman 113 table saw (specifically for 113.299315, but may fit others). This part is a subassembly of part 824360 which is both halves of the guard. ... I have also included a...

Two table inserts for the Craftsman 113.243310 12 inch band saw. Didn't find anything that would work on my saw so drew these up using DesignSpark Mechanical. One is more or less zero clearance the other has a larger blade cutout. I printed with ABS...

Fits the factory guard of vintage Sears Craftsman model 113 contractor-style 10" table saws such as the 113.298142, 113.298032, and 113.298240. Dust hose adapter fits 2.5" Shop-Vac style hoses. Use adhesive to attach the flange to the horizontal...

I believe the Saw blade is facing the wrong direction.My wife found this rusted out table saw for free!I have cleaned it, painted it and started modeling it. The real shaft has some large dings. I wanted a model so I could cut out a new shaft. Then I...

Craftsman Model 113 Contractor Table Saw replacement throat plate with splitter. Requires 2x 10-32 machine screws and 1x 10-32 nut. For small volume printers like an Ender 3 or Prusa MkX, print front and back half then put both pieces together...

I printed this to replace my Craftsman Table Saw blade height adjustment and angle wheel.

Crank for a craftsman 137.228010 table saw. I made the crank handle hole a little undersized so it would have a good bite when you thread the handle in. ... This will work for either the elevation or angle crank and will fit a standard size socket for...

I was wanting to make a miter sled for my Craftsman Table Saw but realized how expensive the rails are so built designed my own. These are 200mm long and have 5 holes for #10 counter sink screws. I am using 4 total for my sled. Hope you...

This is a replacement handle I designed for my Craftsman table saw. My old one broke and I couldn't get it glued back together! Similar parts sell for somewhere between 15-35 bucks online. Also will work with an Ace branded 10" table saw. Scale...

Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts

Replacement handwheel for Craftsman Table Saw, model 113.221620. The handwheels raise/lower the blade and tilt the blade. These fit over the D-shaft. These handwheels may work with any D-shaft with diameter of 3/8-inch. It fits over 5/8-inch of...

... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...

An adapter between a Craftsman 10" Table Saw CMXETAX69434502 and a ShopVac QSP hose with the nozzle removed. Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer!

Replacement Craftsman table saw stand leg end cap. Original broke (see black part in photo). Designed a replacement with more support than the original -- thicker around the sheet metal and taller. ... No supports needed.

The miter locks that come with the [Powertec Featherboard](https://www.amazon.com/gp/product/B084ZF7SWN/) are not compatible with an older Craftsman table saw that I had, so I designed and printed these so I could use those featherboards with my...

Designed to as a replacement for the Craftsman 10" Table Saw Belt Guard Part #: 60252. I've included the Fusion 360 archive file. It's a parametric design and can be customized in many different ways. ...The Pulley Hole Diameter, Wall Thickness, Length,...

I bought the feather board from Harbor Freight but the rail guide was too wide to fit Craftsman table saw, so I made this to fit the rail width around 15.5mm, Once you tighten the knob the rail guide will expand and hold on to the table. ... Including a...

This is a simple replacement for a broken Crank Wheel on my Craftsman Table Saw. The saw uses two of these, one for blade depth and one for the blade angle. Both have a special keyed nut that slides onto the shaft. The size of the wheel is based...

I have a Sears/Craftsman 9 Inch Table Saw and could not find a good file on here that worked. My table saw has a .500 (12.7mm) with the flat to round dimension measuring .400 (10.16mm). Handwheel body is 3.5" in Diameter. The handle knob is 2.5"...

... fillet on the surfaces that led to me printing with supports and then having to sanding it off. I'm not in love with how the surface finish turned out, but it lives under the table of the saw, in a basement, covered in dust, so choose your battles.

Simple model that is helping me configure my garage, done in CATIA with a .stp file for other CAD

... smaller table saw uses a different track than the one I had before so I had to modify the bar. It fits the Craftsman 10-in Table Saw CMXETAX69434502 This is my first creation I have uploaded - comments welcome and appreciated. ... Happy Printing!

Zero Clearance Insert for my Craftsman 10" Bandsaw. Model 113.244513. There is a another on here that is listed for same model, but the blade slot is not where mine is so I had to make my own. ...

Designed for this saw but should fit other Craftsman/Skilsaw table saws with the same type of mitre slot. Intentionally left short so that you can place washers underneath to raise the rail above the slot for gluing to the sled. Very little side to...

... size replica of the original. ...I recommend PLA or any easy to print plastic, since it's just going to be worn away eventually anyway. It replaces Craftsman part number 69156 table insert, and fits band saw models 113244510, 113244512, 113244513.

This is a CRAFTSMAN 10-in 15-Amp Table Saw sawdust exhaust adapter for the 3 gallon shopvac. After downloading several which said their measurements were correct, I found none of them would work. I took measurements and gave the design over to Robert...

A zero tolerance dado throat cover for craftsman 137 table saws. 1/8 kerf. This is an updated version. Last version was slightly off in dimensions. The way the splitter is attached has changed and hopefully will work better. ... The last...

{Edited 3/31/21} This is a zero clearance insert for a 10 inch Craftsman 137 contractor table saw. The insert is 69 mm wide and 255.2 mm long (Measured from the top of the opening bevel located on the top and left edges). The main part of the board...

A simple and compact arbor for using slitting saws on a milling machine. The STP file has a .75" diameter shaft and will fit a slitting saw with a 1" diameter hole. ...The f3d file is the same, but has parameters that can be changed to different shaft...