craftsman table saw insert 3d models

{Edited 3/31/21} This is a zero clearance insert for a 10 inch Craftsman 137 contractor table saw. The insert is 69 mm wide and 255.2 mm long (Measured from the top of the opening bevel located on the top and left edges). The main part of the board...

Two table inserts for the Craftsman 113.243310 12 inch band saw. Didn't find anything that would work on my saw so drew these up using DesignSpark Mechanical. One is more or less zero clearance the other has a larger blade cutout. I printed with ABS...

Customized version of https://www.thingiverse.com/thing:1024418 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1024418

... size replica of the original. ...I recommend PLA or any easy to print plastic, since it's just going to be worn away eventually anyway. It replaces Craftsman part number 69156 table insert, and fits band saw models 113244510, 113244512, 113244513.

Craftsman Model 113 Contractor Table Saw replacement throat plate with splitter. Requires 2x 10-32 machine screws and 1x 10-32 nut. For small volume printers like an Ender 3 or Prusa MkX, print front and back half then put both pieces together...

Model for a zero clearance insert for a craftsman 137 job site table saw... Probably not of any use to anyone; but I couldn't find an insert to use for a dado stack in this saw (one is listed in the manual but I could not find one to purchase) so i...

I printed this to replace my Craftsman Table Saw blade height adjustment and angle wheel.

Crank for a craftsman 137.228010 table saw. I made the crank handle hole a little undersized so it would have a good bite when you thread the handle in. ... This will work for either the elevation or angle crank and will fit a standard size socket for...

I was wanting to make a miter sled for my Craftsman Table Saw but realized how expensive the rails are so built designed my own. These are 200mm long and have 5 holes for #10 counter sink screws. I am using 4 total for my sled. Hope you...

This is a replacement handle I designed for my Craftsman table saw. My old one broke and I couldn't get it glued back together! Similar parts sell for somewhere between 15-35 bucks online. Also will work with an Ace branded 10" table saw. Scale...

Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts

... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...

Replacement handwheel for Craftsman Table Saw, model 113.221620. The handwheels raise/lower the blade and tilt the blade. These fit over the D-shaft. These handwheels may work with any D-shaft with diameter of 3/8-inch. It fits over 5/8-inch of...

This insert can be used with Craftsman scroll saws to reduce the amount of play in small parts as you cut. My detail work was suffering due to the large aperture in my original insert and these did the trick. ...The hole is large enough to accommodate T...

Replacement interlock for a Craftsman Radial arm saw. My original broke. Depending on the accuracy of your printer, you may need to file down the legs. You might want to use acetone to provide extra rigidity. This thing was made with Tinkercad....

Craftsman 113 10" Table Saw Top

Band saw table insert made for Delta 28-206

Replacement insert for an Ozito table saw. ...The slot is slightly narrower so that smaller straight cuts can be made.

Just an attempt at recreating this table insert, for my dads table saw, there are 2 parts to this, the slot and the tongue

Replacement Craftsman table saw stand leg end cap. Original broke (see black part in photo). Designed a replacement with more support than the original -- thicker around the sheet metal and taller. ... No supports needed.

An adapter between a Craftsman 10" Table Saw CMXETAX69434502 and a ShopVac QSP hose with the nozzle removed. Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer!

Replacement insert for an Ozito table saw. ...The slot is slightly narrower so that smaller straight cuts can be made.</p> Category: DIY

The miter locks that come with the [Powertec Featherboard](https://www.amazon.com/gp/product/B084ZF7SWN/) are not compatible with an older Craftsman table saw that I had, so I designed and printed these so I could use those featherboards with my...

This is a replacement for the outer belt guard (part 824359) for a Craftsman 113 table saw (specifically for 113.299315, but may fit others). This part is a subassembly of part 824360 which is both halves of the guard. ... I have also included a...

Designed to as a replacement for the Craftsman 10" Table Saw Belt Guard Part #: 60252. I've included the Fusion 360 archive file. It's a parametric design and can be customized in many different ways. ...The Pulley Hole Diameter, Wall Thickness, Length,...

I bought the feather board from Harbor Freight but the rail guide was too wide to fit Craftsman table saw, so I made this to fit the rail width around 15.5mm, Once you tighten the knob the rail guide will expand and hold on to the table. ... Including a...

 Is your Band saw's table insert torn up, warped, or missing? Try this replacement, it's smooth so your projects don't snag as you make your perfect cuts! This insert measures 56.5mm outside diameter with a 20mm diameter center hole and 3mm thick.

This is a simple replacement for a broken Crank Wheel on my Craftsman Table Saw. The saw uses two of these, one for blade depth and one for the blade angle. Both have a special keyed nut that slides onto the shaft. The size of the wheel is based...

This is a 2 3/4" diameter band saw table insert for one of our industrial band saws used in our school's woodshop. The original had multiple holes cut into it to allow for sawdust blow bye, however we found that these were unnecessary and provided...

I have a Sears/Craftsman 9 Inch Table Saw and could not find a good file on here that worked. My table saw has a .500 (12.7mm) with the flat to round dimension measuring .400 (10.16mm). Handwheel body is 3.5" in Diameter. The handle knob is 2.5"...