craftsman table saw miter bar 3d models

This is a replacement miter track bar for the Rockler Featherboard which fits my Craftsman 10-in Table Saw. This smaller table saw uses a different track than the one I had before so I had to modify the bar. It fits the Craftsman 10-in Table Saw...

Miter bars sized for my Dewalt DWE7485WS with holes for M5 screws

The miter locks that come with the [Powertec Featherboard](https://www.amazon.com/gp/product/B084ZF7SWN/) are not compatible with an older Craftsman table saw that I had, so I designed and printed these so I could use those featherboards with my...

Bar runner made for miter slot on Ryobi RTS23 table saw. The bar is 220 mm in length (8.67 inches) and has 3 screw holes. The bar was originally designed to work with a cross cut sled. I have not verified but I believe this will fit other Ryobi table...

Maybe next weekend, older: This Miter bar was designed to replace the miter bar that came with the Harbor Freight feather board that i cannot get to secure into the t-slot of the Harbor Freight table saw. Design is working decent since it is a t-slot...

I designed this miter bar because the one included with the saw has too much play. The aluminium miter slot is 21mm (when new) but will wear down with use and it will wear more at the front than the back.  Instructions:Print the test piece...

I was wanting to make a miter sled for my Craftsman Table Saw but realized how expensive the rails are so built designed my own. These are 200mm long and have 5 holes for #10 counter sink screws. I am using 4 total for my sled. Hope you...

I printed this to replace my Craftsman Table Saw blade height adjustment and angle wheel.

This is a replacement laser holder for a craftsman miter saw. You will need 2 screws to attach it to the holes on the saw. ... Designed in fusion 360.

... 10 in. ...Compound Miter Saw Replacement trigger. Model No. 315.235360. The original saw's trigger broke and is no longer available to purchase. ... This trigger was designed in sketchup and replaced the broken trigger directly off the 3d printer.

Crank for a craftsman 137.228010 table saw. I made the crank handle hole a little undersized so it would have a good bite when you thread the handle in. ... This will work for either the elevation or angle crank and will fit a standard size socket for...

I built this miter saw table for our shop. ...I put Polypro for countertop and ABS white for the bottom shelf and it work great.

Made this for a coworker; Replacement Craftsman 12" Compound Miter saw handle. The old handle broke off, just had to lightly tap this handle into place. Glue may hold it better, but it is a solid fit by itself. ... Created in fusion 360

... me to print it for you please check out my Etsy page. https://www.etsy.com/CuriosByCalvin/listing/1089294407/137212290-craftsman-miter-saw-handle?utm_source=Copy&utm_medium=ListingManager&utm_campaign=Share&utm_term=so.lmsm&share_time=1632332951144

Required: qty 2 1/2" diameter x 2.5" long dowel pins qty 2 1/4" diameter x 2.0" long dowel pins Based on the Woodpeckers Table Saw Gauge to align the saw blade to the miter slot. This design has been enhanced with integrated 'trays' for storing the...

This is a replacement handle I designed for my Craftsman table saw. My old one broke and I couldn't get it glued back together! Similar parts sell for somewhere between 15-35 bucks online. Also will work with an Ace branded 10" table saw. Scale...

I couldn't find anything on Thingiverse that matched the ID of my miter saw so I just remixed the one by Kachidoki. ...The part that inserts into the tool is 31.5mm OD and 20mm long.

Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts

... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...

The miter fence holder for my craftsman table saw (Ryobi BT3000 clone) broke. This was no surprise because it is a thin plastic part with sharp inside corners. I was able to find a replacement part at the link below, but it seems to be going out of...

Replacement handwheel for Craftsman Table Saw, model 113.221620. The handwheels raise/lower the blade and tilt the blade. These fit over the D-shaft. These handwheels may work with any D-shaft with diameter of 3/8-inch. It fits over 5/8-inch of...

This a replacement part for a Hitachi sliding miter saw model C 10FS. This may work on other Hitachi miter saws. The table inserts become damaged after much use and need replacement. The inserts are longer than the 3D printer bed, so they are...

This a replacement part for a Hitachi sliding miter saw model C 10FS. This may work on other Hitachi miter saws. The table inserts become damaged after much use and need replacement. The inserts are longer than the 3D printer bed, so they are...

This a replacement part for a Hitachi sliding miter saw model C 10FS. This may work on other Hitachi miter saws. The table inserts become damaged after much use and need replacement. The inserts are longer than the 3D printer bed, so they are printed...

I got this new saw, but some things make me crazy like trying to stick the end of the miter into a hole of the same size, this part is open on top so it goes in from above, much easier!!!

This new saw is very nice, but has a few issues with the attachments, print this and you will never experience the miter slipping again. I put the graduations at 2.5 degrees and placed a mark at the important 22.5 degree spot. you will need a...

Miter bar runner for a Dewalt table saw and POWERTEC T-Track knobs. Knobs that go with this runner: https://smile.amazon.com/gp/product/B01N5WC8BK This runner is intended for the DWE7485 compact jobsite table saw, but likely fits other Dewalt table...

The oddly-shaped throat plate insert for Craftsman Miter Saw #137.212290 wasn't too hard to recreate, which is great, since it's been discontinued and no longer available anywhere. Original part # is 2BK8. ...

The miter slot on the Craftsman saw is 16mm by about 7mm deep so I used the same spacing for the holes as bruckj and made the slide fit the miter slot on the Craftsman saw. I had already bought my hardware so if you did the same after seeing bruckj's...

... to make it I thought others might also need this part. CRAFTSMAN MITER SAW HANDLE 137.212290 2BPS CONNECTOR Note: It appears 3D Printing this part it is not strong. ... I print in PLA and have tried 3 different times now and the part always cracks.