crochet pen holder 3d models
357735 3d models found related to crochet pen holder.
thingiverse
Put together this phone and crochet hook/pen holder using the turtle design by YahooJAPAN (https://www.thingiverse.com/thing:182332). Accommodates phones thinner than 10mm, crochet hooks under 12mm in diameter. ...Blender files are included should you...
thingiverse
Converted the Sea Turtle scanned by pmoews (https://www.thingiverse.com/thing:421809) into a phone and crochet hook holder. Printed in metallic copper from BotFeeder (Canada). Due to the nature of metallic materials, it looks a lot better in...
prusaprinters
<p>Printed with PLA, at 0.3mm, 15% infill.</p><p>No support needed when printing top and bottom separately.</p><p>I've glued the top and bottom parts.</p>
prusaprinters
this pen was designed to use a standard Bic pen cartridge. Hook sizes K and HI have added a thicker model for the K design I noticed on one of my prints that the walls would be better thicker
thingiverse
this is a 4X4 inch coaster holder for some coaster my wife crocheted.
thingiverse
I modelled this Crochet Hook holder for my partner to crochet hooks with ergonomic handles. I wanted it to be modular, so each piece is printed separately. The pieces are designed to be screwed together, and the threads are part of the model. I...
thingiverse
Custom organizer stand for a special set of crochet hooks. ... *New file has adjusted sized for clearance printing.
thingiverse
A cotton spool holder for crocheting. Dimensions: Stand height: ~15cm Stand length: 10cm Width of stand with rod: 17cm. Rod height from ground: 12cm. Rod diameter: 1.5cm Rod cap diameter: 2cm. Instructions: - Pieces include: Stand (t...
thingiverse
Crochet à serviette Print Settings Printer: Afinibot Rafts: No Supports: Yes Resolution: 0.2 Infill: 30
thingiverse
Crochets pouvant avoir plusieurs utilisations. ...Réalisé pour soutenir des barres leds Epaisseurs de couches : 0.20 Remplissage : 20% Th: 210°
thingiverse
crochet épaisseur 15 idéal pour suspendre un pot de fleur, pour mettre accrocher un sac sur une poussette ..... ...
thingiverse
Crochet réalisé pour torchons mais peut être utilisé pour pleins d'autres choses... Gants de toilettes clef etc. Emplacement prévue pour que la tête de vise vienne ce noyer dans le modèle une fois fixé. ... n'hésiter pas a poster vos réal, Bon print.
thingiverse
A little display stand I made for fountain pens but it also works for anything pen/pencil-shaped, like crochet hooks. Print orientation should be on its "back" so that the arms print straight up into the air. ...No supports necessary.
thingiverse
crochet d'accroche pour le spray-can holder (https://www.thingiverse.com/thing:1436529) espacement du croche 15mm.
thingiverse
MAJ: le crochet se clipse sur 2 tubes afin de ne plus tomber lorsque l'on prend sa serviette. ... crochet pour porte serviette avec tube de 23 mm hook for towel holder with 23 mm tube
thingiverse
This is a crochet holder that I made for my wife. Easily holds 1 crochet hook, several needles, and stitch markers. ... It can also be used to hold knitting needles.
thingiverse
A crochet hook holder with a range of hole sizes that fits in a wool bowl. The sheep are both ornamental and serve as handles to lift the holder from the bowl. Both are designed to print without supports. A side effect of which is that the wool...
pinshape
A crochet hook holder with a range of hole sizes that fits in a wool bowl. The sheep are both ornamental and serve as handles to lift the holder from the bowl. Both are designed to print without supports. A side effect of which is that the wool...
prusaprinters
An updated version of my last knitting needle holder. I've adjusted the design so that it prints great without any supports. ...Make sure that the holes face down on the bed, for best results. I added a small angled pocket on one side to hold darning...