dart xl 3d models
10028 3d models found related to dart xl.
thingiverse
simple camera handle for zohd dart xl mount. ... picture explains what it is.
thingiverse
This is the module and nose plate I created to allow an enclosed pan-tilt setup with the ZOHD Dart XL.
thingiverse
Made this to close the front panel of the dart xl , i use something the fpv cam in front and the hd cam above the wing . two versions , R6 have my nickname on it . ... the fusion 360 file is attatched for those who want to modify and/or add...
thingiverse
This is an easy print replacement motor mount for the ZOHD DART XL. The original is only supported by the bottom half with some less than optimal glue so it will come off like mine or flex. This is a little more solid and has a short stabilising...
thingiverse
This is a simple part made to fit the Runcam Split (I'm using V2 here) into the Dart XL from ZOHD. It fits snugly into the nose like the included foam inserts for different cameras, and the Split mounts into it. There are openings to allow airflow...
thingiverse
I've remodeled the ZOHD Dart XL's firewall, keeping an eye on the model by hi_im_jonn0. - modeled the curves according to the original wooden firewall - enlarged the holes for the thumbscrews - lengthened the "pipe" section for a better fit ...
cults3d
I've remodeled the ZOHD Dart XL's firewall, keeping an eye on the model by hi_im_jonn0. modeled the curves according to the original wooden firewall enlarged the holes for the thumbscrews lengthened the "pipe" section for a better fit Any...
thingiverse
Remix of a Great dart xl motor mount, i wanted to angle the rear deck so that it matched the angle of the fuselage for better bonding, also on mine the Motor mount plate angles did not match up to the fuse so i changed that until they do, now it...
prusaprinters
This is a simple part made to fit the Runcam Split (I'm using V2 here) into the Dart XL from ZOHD. It fits snugly into the nose like the included foam inserts for different cameras, and the Split mounts into it. There are openings to allow airflow...
thingiverse
Modified the Cam holder and the AirUnit Mount for the ZOHD Dart XL
cults3d
Modified the Cam holder and the AirUnit Mount for the ZOHD Dart XL
thingiverse
ZOHD Dart XL FC holder. ...The main spar is supposed to hold it in place.
thingiverse
Designed hold the Caddx Polar VTX for easy mounting on top of the ZOHD Dart Xl. The bottom curvature is made to fit the top of the dart xl. ... Four screw mounting holes are provided for easy attachment.
thingiverse
Zohd Dart XL DJI Cam mount. ... Holds the DJI cam without screws, but can be used if necessary.
thingiverse
A simple skid to protect the downward facing wingtips on your Dart XL See video for more information https://youtu.be/36a_YmIp3Zk
thingiverse
... to put on the top of the ZOHD Dart XL electronics bay cover. ...It is angled 15° to the back. Print it in PETG or in TPU. Tested with the Eachine TX805 Transmitter I'm building the ZOHD Dart XL Extreme right now - so more parts to come
thingiverse
...I took his design and slightly altered it to match the Dart XL Enhanced supplied Motor Mount. I shortened the length by 2mm and removed the taper on the motor mount face plate. It's not perfect but really close. I only had one issue before printing.
thingiverse
Just a quick replacement battery bay plate for the ZOHD Dart XL, as none were available yet. I don't normally design so my require adjusting/remixing to suit needs. ... Printed in PLA.
thingiverse
This thing is an adapter I made to upgrade the motor on my dart xl to fit a sunnysky 2814/1200Kv with 4200mah battery this wing go crazy the plate will be attached using the original mounting holes on the wing. ... Required parts: - x4 10mm M3 hex...
thingiverse
Replacement motor mount for the ZOHD Dart XL. A bit more built into the fuselage for reinforcement as the other one was quite easily broken and sometimes glued off angle. I don't normally design so this may not be perfect. ...feel free to improve as...
thingiverse
This is a reinforced firewall for the ZoHD Dart XL Extreme. It has the trust angle correction already implemented. To install it, remove the original firewall. Make some holes with a sharp knife on the position of the "spikes". Put some glue on...
thingiverse
Upgrade Kit for VTX, Matek GPS, SMA Mount for Antenna Zohd Dart XL http://bit.ly/2EbdXaT Matek F405 Wing http://bit.ly/2DJCpz8 AKK Infinite http://bit.ly/2rTCJEd Runcam Eagle 2 Pro http://bit.ly/2ReleNn Runcam 3S http://bit.ly/2EPHVBR My 3D Printer...
thingiverse
Replacement low profile back hatch for ZOHD Dart XL Beds smaller then ( 235mm x 235mm) use the 2 piece hatch, but with carefull placement the full size 1 piece hatch will fit diagonally. ... I advise to print a single skirt with 1mm offset from print...
thingiverse
I made this taller pan-only gimbal for my Dart XL since I didn't want to pierce through the foam to fit the servo through the front canopy. **UPDATE 01/02/2018:** I've uploaded an improved version of the bottom part of the RCSplit mount. It has...
cults3d
Replacement low profile back hatch for ZOHD Dart XL Beds smaller then ( 235mm x 235mm) use the 2 piece hatch, but with carefull placement the full size 1 piece hatch will fit diagonally. ... I advise to print a single skirt with 1mm offset from print...
thingiverse
A cleaner way to mount an OLED display _(I2C, 128x32)_ in your Dart XL. Use two cable ties to attach it to the main spar inside the body. **This is meant to be printed in TPU**, it might need some slight upscaling or heating if printed with rigid...
thingiverse
This is a latch that is designed to replace the magnetic catches on the battery bay of the ZOHD Dart XL. Why? I've installed an Eagletree MicroVector in mine and the best place for the GPS and compass unit was way too close to those magnets to...