dart zone pro mk3 3d models

Minimized barrel for the Dart Zone Pro MK3. Also Included: STEP file for a blank barrel. For Remixing your own barrel designs. Prints Without Supports; overhangs should bridge. Update: added adapters to install a Nexus Pro cosmetic flash hider...

Now you can make your own with this unique cover for the Dart Zone Pro Mk3. This minimalist battery extender gives enough space to fit any 2200 mAh batteries and simply covers the existing hole. this was designed by me in Tinkercad, and is not...

Now you can make your own with this unique cover for the Dart Zone Pro Mk3. This minimalist battery extender gives enough space to fit any 2200 mAh batteries and simply covers the existing hole. ... this was designed by me in Tinkercad, and is not for...

This is my battery box for a Dart Zone Pro MK3 (MK-III). I designed this battery box for use with 4x or 8x LifePO4 batteries. It lets you use your 3.2v LifePO4s only. Fits perfectly with no modification required to the MK-3. NOT FOR USE WITH 3.7V...

I recently finished a big Dart Zone Pro Mk3 mod. During the build, I wired in a voltmeter from Foam Pro Shop and wanted to mount it where the insert is to the right of the battery tray. Scope7Tango had already done a great job of modelling the DZP...

I made a post to r/Nerf showing a video of the issue: https://www.reddit.com/r/Nerf/comments/10xf4b6/dart_zone_mk3_feeding_issue/ I modified the pusher bringing the part that pushes the dart half an inch further forward, to make it push the darts far...

Replacement Dart Pusher for the Dart Zone MK3 flywheel blaster. Designed to correct problems with Jamming, and Double-Feeding. in stock form on release**, the MK3 has problems with jamming when using Talon magazines as well as problems with...

Beefy rev switch support for the MK3. Should prevent the switch from breaking off its switch posts from all sides. ...Direct fit.

Improved and extended selector lever for the DZP MK3. ... Print at full infill as you have to drill out the screwhole (5/64' bit)

My DZP MK3 was having occasional inconsistent Rev Trigger response. the problem appeared to be that the plastic mounting was flexing this brace stabilizes it. ... just drops in, gets held in place by shell.

Remix of HapHazardlyNamed’s awesome sling adapter. ...I wanted to cut down on the MK3’s length, so I modified it slightly so that it covers the rear of the DZP MK3 after cutting off the stock tube.

Side inserts I made for the MK-3/MK-III. They are the front inserts that screw in and the back/side inserts that snap in. ...These are plain inserts that can easily be modified for additional designs or lettering.

Two finger rev trigger for the MK-3. ...Wanted something a little bigger and more natural feeling when gripping the trigger frame.

Custom pusher arm for the MK-III. The factory ones are prone to break so I beefed this one up considerably. ...Direct fit and direct drop in.

Available for purchase and download on Cults3D https://cults3d.com/:1088794

Not a remix. My first one never published correctly. Beefier version of the stock pusher arm. ...The original one is prone to breaking when you upgrade your pusher motor to a faster ROF.

Replacement rev trigger switch that allows the trigger to cycle without revving the blaster. The factory rev trigger lock requires the rev trigger to be fully depressed before the trigger will cycle. This lock delete allows you to remove blockages or...

Motor mount for a Dart Zone Pro MK-III auto pusher. Should secure most aftermarket 130 sized motors when upgrading the pusher motor to a more speedy model than the factory unit. ... Added version 3 - reinforced bridge and vertical mounts.

Not much explaining needed for this, its a G36 style magazine release made to work with the Dart Zone Pro MK3. It allows for 2 ways to release the mag; either grab the mag while pushing on the vertical tab, or simple use your middle finger to push...

A Shortened Magazine Release for the Nexus Pro, Max Stryker, and Dart Zone Pro MK3 When primarily using half-darts with the magwell adapter, the main magazine release is not used. ...So I reduced its size to get it out of my way. prints without...

Quick model of the DartZone Pro Bamboo Dart, as accurate as I felt most people would need. All features are modelled, including the ribbing on the stem of the dart. The only thing I left off were the slight mold lines on the foam. Feel free to use...

This is the template for a simple plastic barrel that can be used in the Dart Zone Pro Mk1. I created it in OpenSCAD so it can be easily customized to a dart type in order to get a proper fit in the barrel. That said, I find the metal barrel...

Short Dart Magazine swag: - "DZNP_Adapter_Flare.stl" - "DZNP_Adapter_Release.stl" Foregrip (EDITED 9/16/2020: added 2mm of thickness to the flat most part to provide more strength after I had a failure along that piece) - "VFG_Stubby_DZNP.stl" -...

A half dart only conversion for the Aeon Pro. I needed it to remove some of the initial slack and shorten the priming distance for a pump kit that I have in the works. • Shortens the priming distance and removes some slack. • Friction fits...

Dart zone Aeon Pro Foldable Shoulder stock

... from getting pushed around and block the catch. ...The base is sized to fit right into the plunger tube cap of the Aeon Pro and keep everything centered. I used it with roughly 9cm K31 to reach ~100fps with Dart Zone Pro Chili Darts cut to 35mm.

The buttstock on the dart zone pro mk1 collapses when theres too much pressure. I whipped this up real quick in the hopes that it will help keep the buttstock from collapsing. I glued this on only one side so you can still open the blaster if...

This is an extender for the Dart Zone Nexus Pro buffer tube. As simple as that. There is only one hole to put the stock on, but I'll design a longer alternative if there is demand. Proudly designed with Blender. *If it loads in your slicer too...

MOLLE holsters for the Dart Zone Pro MKII Speedloaders. Use the offset MOLLE clip for mounting two side-by-side; use the mirror feature in your slicer to go the other way. ...Slide the quick fastener through the webbing to attach.

This is my 3d model of an alternative barrel attachment for the new Dart Zone Nexus Pro dart blaster. The existing barrel is a friction fit, and this was modeled from caliper measurements of that exisiting barrel. All in all it is about 210mm or 21cm...