dillon 550 spent primer catcher 3d models

this is a spent primer catch container for Dillon reloading press and may work on other presses as well. you will also need thing https://www.thingiverse.com/thing:2312035 and 1/2in ID clear flexable tubing. ...

My old XL650 started dropping spent primers after a Dillon warranty repair. Rather than go with an aftermarket tube and bottle fix I remade the factory spent primer cup so that it extends under station 1 more, and I think it holds a bit more spent...

Spent primer chute Dillon Super 1050. Use a hose with 3/8" inner diameter. Hose clamp probably not required as the hose fits pretty tight. I've only used on small primers, however, it is a 6mm funnel so it should work fine with large primers. Feel...

spent primer tube for dillon xl650 minimized size design

Replacement empty primer tray for Dillon 550. I've included a short model and a large one. ...I've not tested the large one but the small works well.

Everyone has the problem with the spent-primer-bin that regularly shoots a spent primer into your room. This adapter replaces the bin+mount and uses the same screws. The only thing you need is some plastic-flexible hose with outside diameter of 12mm,...

This print replaces the Dillon XL650 primer catcher with a hose adapter. The inner diameter has been made large enough that if two primers were to drop at the same time that they can't bind and block up the tube. I use a clear vinyl tube with an...

This is a configurable version of 'Dillon 650 Spent primer tube-mount' by BlaRock86. I did not have any 12 mm tubing available so I made the piece configurable for outer diameters between 12 and 17 mm. The photos show the 14 mm version in action. I...

Replaces metal shoot on Dillon 450 progressive press. ...Keeps the primers from flying out of the side and into your bins or face. ...Uses 5/8" or 15mm tubing.

Primer chute for Dillon rl1100/1050. use a zip tie to lock on the tube. put a water bottle at the other end for thousands of rounds before emptying. I printed vertically with some tree supports. Requires a 3/8 inch OD tube. ...(1/4 inch ID)

Primer chute for Dillon rl1100/1050. use a zip tie to lock on the tube. put a water bottle at the other end for thousands of rounds before emptying.</p> <p>I printed vertically with some tree supports.</p> <p>Requires a 3/8 inch OD tube. ...(1/4 inch...

about 20-30% of my used primers bounce off the 550 itself and then end up on the floor. I can see exactly where they hit and it just needs a little help from a funnel. So I made this to make sure they go into the tray. It snaps right on, OR you...

spen primer funnel based off original part the bottom has a 1in diameter for a hose v2 is a taller model that almost touches the press

I bought a Frankford Arsenal M-Press coaxial press recently and the spent primer catcher was missing from the box. It was faster to mock this up and print than it would have been to call the company and wait on shipping, especially since it's right...

He was tired of the factory cup not properly catching primers and asked me to design one with an up- and rearwards-leaning ramp to catch them better, and says this one has yet to miss a primer. This fits exclusively on a Dillon RL 500D multistage...

As far as I can tell, there aren't any spent primer catchers for the Texan Loader presses. This one slips under the spent primer hole for conveniently catching primers instead of letting them roll everywhere. Print with supports everywhere. I...

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/3MrwmTh2qMK

Dillon 550 spent primer cup with 1/2" hose barb Made a stronger connection to the hose fitting V2 has the connection to the press more offset and shorter

Trigger tray big than normal, with upper bevel to facilitate the capture of the trigger. ...for my printer I reduced 99% on the x axis, but it changes just 4 tenths.

Suitable for the RCBS Rockchucker Primer Catcher Remix V3 https://www.thingiverse.com/thing:4250348 However, it can be connected to all systems that use 15 mm tubing. I added a V2 with thicker walls on the side. That makes the bin more rigid. I...

Suitable for the RCBS Rockchucker Primer Catcher Remix V3 https://www.thingiverse.com/thing:4250348 However, it can be connected to all systems that use 15 mm tubing. I added a V2 with thicker walls on the side. That makes the bin more rigid. I...

A conventional 15 mm hose fits into the holder. Suitable for the RCBS Rockchucker Primer Catcher Remix V3 https://www.thingiverse.com/thing:4250348 However, it can be connected to all systems that use 15 mm tubing. I added a V2 with thicker walls on...

replacement for a broken chute for a dillon square deal b press

I love the new primer catcher my RCBS Rock Chucker sports:http://www.thingiverse.com/thing:1223108 Might also work with this primer catcher:http://www.thingiverse.com/thing:148190 Or its predecessor:http://www.thingiverse.com/thing:84047 While it...

Shotgun spent primer tray for MEC Versa Shotshell loader. ... Fits nicely, and doesnt move around.

here is my design for a identification system for my dillon 550 primer tube. i had a tough time remembering what primers i had loaded into the tube between loadings. ...this is a reminder as to what is there.

Toolhead stand for Dillon 550

A 6 conversion Holder for Dillon 550

This model is an improved version of Dillon's cast toolhead for the 550 series presses.