diy wire holder for soldering 3d models
2438106 3d models found related to diy wire holder for soldering.thingiverse
I made this to hold my excess wire for my soldering projects. Print Settings Printer: XYZ DaVinci AiO Rafts: ...
thingiverse
Stand for soldering spool wire: For spool max wide 70 mm and diameter max. 90 mm. ...(bigger than that won't fit) Inner minimal diameter axle hole is 9mm (smaller than that wont fit).
thingiverse
[**Edit 17.02.2019 (V2)**] Modified the holder to: - Make it smaller - Make it stronger - Make the led strip at the same level as the pins - Add blocker so that it doesn't move [**Original**] I bought [Led strip from...
thingiverse
Fits up to 10 soldering tips (7 mm outer diameter), one spool of soldering wire (19 mm inner diameter), one tin of flux (66 mm outer diameter). Print all the parts and glue them together by matching corresponding holes and protrusions. ... ...
thingiverse
Created a holder for soldering paste and soldering wire. ...Two parts construction held together with an M3 screw for easier printing.
cults3d
Created a holder for soldering paste and soldering wire. ...Two parts construction held together with an M3 screw for easier printing.
thingiverse
Small Soldering Wire holder with outfeed hole on a 75x35mm base plate.
thingiverse
I found many designs for a soldering wire holder, however since I'm printing on 8 by 8 printer , I couldn't print most of them. Plus I really enjoyed designing the tube fit to the base of the holder. There are positions for M3 / M4 screws since I...
thingiverse
so as i do 12volt installations every day for a living, i always got tired of my soldering wire spool rolling off and moving and such, so i made a simple holder for it. the center is not actually center on the base. ...(i did that on purpose) i made it...
thingiverse
Joining two wires with solder is awkward holding them still to make a tidy job easier with this simple little stand to hold wires together for soldering slide over some heat shrink and the jobs a good one. ... Print Settings Rafts: ...
pinshape
SummaryJoining two wires with solder is awkward holding them still to make a tidy job easier with this simple little stand to hold wires together for soldering slide over some heat shrink and the jobs a good one. ...Print SettingsRafts: NoSupports: ...
thingiverse
Soldering wire joiner holder Suits 10 - 30 AWG gauge wire If you find this useful and would like to show your support, please buy me a coffee :) https://www.paypal.com/paypalme/ikom Let me know if you have any suggestions to improve my design or have...
thingiverse
Its a soldering base that helps you hold the cables/wires while you are soldering. ... Wire/cable diameter : 0,50/0,75/1/1,5/2,5 (mm)
cults3d
Its a soldering base that helps you hold the cables/wires while you are soldering. ... Wire/cable diameter : 0,50/0,75/1/1,5/2,5 (mm)
grabcad
A stand to put your spool of soldering wire on while using it to stop the roll from rolling all over the table when you have the iron in one hand and the soldering wire in the other.
pinshape
SummaryHere is a stand to hold wires while you solder. ... It has two different grooves that will handle from 10awg on up.
thingiverse
Here is a stand to hold wires while you solder. ... It has two different grooves that will handle from 10awg on up.
thingiverse
Convenient two-coil solder holder, printed without supports in one piece, quite stable, I have been using this for a couple of years. For coils with a large opening, an adapter ring is recommended. Source included. Удобный двухкатушечный...
thingiverse
This contraption holds wires end-to-end while you solder them. They use magnets to attach themselves to a metal work surface and apply slight clamping pressure. They clamp down on the wire like a clamshell, with the foam applying light pressure. ...
thingiverse
I thought I'd throw my hat in the ring with a base to hold soldering wire. I know there are a zillion of these on Thingiverse, but I wanted some things: To practice modeling things in Onshape. Magnets! Looking at the models around, I figured the...
thingiverse
its easy to print , there are a lot of holders out there but i think this is the simplest , you can insert an old pen to hold the spool , it will hold almost all kind of spools and even two small ones. ... i hope you liked it.
thingiverse
Soldering holder - it makes easier to solder audio jack into the PCB. More information about this (ant other) project can be found here: https://daumemo.com/diy-micro-usb-c-to-3-5mm-adapter-and-headphone-amplifier-part-4/ Printing: Printed with an...
thingiverse
Replaces the original wet sponge holder. ...Print Settings Printer Brand: RepRap Printer: Tronxy PA802 ...