doepfer a 180 3d models
2144418 3d models found related to doepfer a 180.grabcad
Doepfer A-100 Bus Board v5For designing your own modular synthesizer.I'm not an expert, but the dimensions are correct and it should be good enough for designing a eurorack case
thingiverse
This is designed to work with the A-180 By SwarleyAUS https://www.thingiverse.com/thing:2000666
grabcad
Doepfer DIY Power SupplyI'm not an expert in 3d-modeling but dimensions are correct and it should be good enough for designing a eurorack case.
thingiverse
I experimented a bit to get a grippy pattern that still printed ok on my poorly calibrated cheap printer. A freecad file is in there if you want to play with it. The slim one has a wide skirt for fine adjustments. The big model is the same height...
thingiverse
This is a muzzle device I designed for the AW Custom P08 airsoft A-180 blaster conversion kit. I printed it in copper PLA instead of blaze orange. ...I made a groove for an o-ring in case you don't want to permanently install it.
cults3d
This model of the Blaster is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016. ... Useful...
cults3d
This model of the Blaster rifle is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016. ... Useful...
thingiverse
I was disappointed with the other offerings for the A-180. So, I built one with 3D printing in mind and a working trigger! To improve on its aesthetics, I wanted to have a few parts to assemble after printing. It should be obvious where the pieces...
thingiverse
I built this as a filament guide for my printer, i have my drybox on top of the enclosure and run my filament in the back wall, so i needed a nice 180* turnaround for the material, its intended to be mounted on 1/8" flatbar (i am using aluminum 3/4"...
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348861 Instructions Using the following options: Diameter = 15 Bottom = 1 Direction = -1 Top = 1 Balls = 1 Resolution = 0.20 Twist = 180
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348861 Instructions Using the following options: Balls = 1 Top = 1 Diameter = 20 Twist = 180 Resolution = 0.20 Bottom = 1 Direction = -1
pinshape
This model of the Blaster is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016. Model dimensions: - length - 439.5 mm - height - 182.5 mm - width - 57.5 mm - length of the...
pinshape
This model of the Blaster rifle is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016. Model dimensions: - length - 940.5 mm - height - 182.5 mm - width - 57.5 mm - length of the...
grabcad
... GRUNDFOS ALPHA2 L. ...As additional the ALPHA1 now features a two digit display showing the actual pump power consumption in Watt Find much more product variants and CAD files on our Online Products selection tool http://product-selection.grundfos.com/
thingiverse
... ...http://www.thingiverse.com/apps/customizer/run?thing_id=53451 Instructions Using the following options: approximate_number_of_teeth_on_sun = 9 number_of_planets = 5 tol = 0.35 nTwist = 1 w = 6.7 P = 45 T = 50 D = 180 number_of_teeth_on_planets = 7
thingiverse
These are some parts to attach a Doepfer power supply to a breadboard. The parts are: - a protection case for the power supply - some clamps to slide the protection case on the edge of a breadboard - some protection caps for unused pins The plate...
thingiverse
I had bought a Doepfer A-100 Diy kit but could never get the rails to fit exactly.
cgtrader
This model of the Blaster rifle is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016.
cgtrader
This model of the Blaster is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016.
cgtrader
This model of the Blaster is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=735038 Instructions Using the following options: a_mani = 180 ds_fan2 = 3.4 ds_fan1 = 3.4 d_fan2 = 40 d_fan1 = 40 a_cone = 100 az_mani = 20 $fn = 90 n_angle = 0.501 l_mani1 = 0 t_wall = 1.5...
cults3d
This model of the Blaster is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016. ... Useful...
pinshape
This model of the Blaster is based on the Blaster pistol A-180 from the movie Rogue One A Star Wars Story 2016. Model dimensions: - length - 499.5 mm - height - 182.5 mm - width - 63.7 mm - length of the...
grabcad
... ! ... il ne faut pas oublier qu'il faut prévoir 5' maximum entre chaque barreau vertical pour le code canadien. Alors il se nomme GC 120-180. Pour plus de 180" il faut prévoir un troisième barreau vertical au centre donc un autre garde ilogic.
thingiverse
Replace the wooden bar below the modules from your Doepfer P6/P9-Suitcase with these Multiples-Frames. I used Doepfer A180-2 Multiples, but you can wire some jacks by your own as well. ... Print: 1 x multiplesFrameLeft.stl 4 x...