dust deputy 3d models
16356 3d models found related to dust deputy.grabcad
Oneida Air Systems - Dust Deputy dust separator, dust cyclone, dust collector. Did the best I could using calipers and a nice ruler. ...Model units are inch.
grabcad
CNC cuttable 5 gallon bucket lid to fit Dust Deputy cyclone on top of.
grabcad
These are the supports to add to the Dust Deputy to give it a little strength when attaching to a bucket top.
thingiverse
The vacuum hose threads onto the adapter, and the inside is tapered to fit tightly onto the Dust Deputy. It will fit both ports on the dust collector. ...The hose I use is in the following link: ...
thingiverse
The bottom 30 mm attaches to the Dust Deputy as it has a small taper inside that fits the taper on the Dust Deputy. The top 40 mm is where you push the hose into. It is best to add a liberal amount of silicone to the hose end first and let it dry...
prusaprinters
The bottom 30 mm attaches to the Dust Deputy as it has a small taper inside that fits the taper on the Dust Deputy. The top 40 mm is where you push the hose into. ...It is best to add a liberal amount of silicone to the hose end first and let it dry...
thingiverse
Edit: I've reworked the hose connections between the Dust Deputy and the Rigid shop vac to use a section of Rigid 2 1/2" vacuum hose after creating a hose wye for my router table. The .stl files are delineated either DD CH for Dust deputy coil hose,...
thingiverse
simple coupler to interface an inventables xcarve dust shoe hose (1.5"ID) to an oneida dust deputy cyclone extractor (2"OD). ...
thingiverse
If you have a Dust Deputy Cyclone dust collector in your shop, this will mate with the horizontal tube off it and connect to a 2" vac hose. ... Instructions Print and shove it on the Dust Deputy...
thingiverse
... side of the Dust Deputy DIY to a 2" vacuum hose (2.25" OD on vacuum hose). ... It includes cut-outs so that a hose clamp can be used to fix it to the Dust Deputy, and it fits deep onto the Dust Deputy input (which is a 2 step part, it snugs onto both).
thingiverse
... it to the lid of my bin. ... I wanted to not have to worry about the weight of the Dust Deputy every time that I needed to empty the bin. ... This way, I have the lid connected to a hose which I can just raise and lower without moving the Dust Deputy.
thingiverse
Originally intended for the Dust Deputy Cyclone dust collection system, this adapter allows you to use smaller vacuum hoses. Converts 2" O.D. port to a 1.25" O.D port. ... Fix: Updated the dimensions of the small end.
thingiverse
Simple, slightly overbuilt, adapter to go from the inlet on a dust deputy to the small sized shop vac hose that came with my 8gal shop vac (ID ~53mm/2in on the connection). ...Should work for a the full 2in hose, but you'll probably loose a bit of...
thingiverse
Adaptors for Oneida Super Dust Deputy 5" to fit a 5" hose to connect to the Harbor Freight Dust collector inlet, or other applications that use 5" hose 2 Versions, they are basically the same but the larger is 6.5" tall and the smaller one is 3.5"...
thingiverse
This slips easily into the opening in the Super Dust Deputy as designed but is not sloppy. It can be secured with foil tape or a bead of sealant. You should print a test ring of the larger side to ensure fit in your cyclone. I was unable to get...
thingiverse
The bottom flange of the Dust Deputy can also be warped and bolt pressure is usually strong enough to give you an air tight seal, but if not, put some silicone on it before bolting it down. Workshop WS25022A 20 foot 2-1/2" hose: Your original short...
thingiverse
An adapter for the Dust Deputy DIY cyclonic separator input, to connect a shop vac 2" hose to. This is modeled to the multiple steps of the input, but it really needs a hose clamp to hold it firmly in place. It'll hold well if you firmly press it...
thingiverse
A nice little adapter from the Festool Sleeved hose to the Oneida dust deputy. Don't forget to add some of the foil tape to keep the ground path! The original design didn't print quite right, but I figured I'd try it anyway. It worked great! Then I...
thingiverse
this in a flange for shop fox w1661 and using a oneida super dust deputy 4/5 cyclone 6"
thingiverse
Adapter for DeWalt Stealth Sonic hose to a Dust Deputy 2.5. I added thin neoprene tape on the outside perimeter to help seal. ...YMMV.
thingiverse
This part connects the the 5" Inlet Port for the Super Dust Deputy Dust Extraction Cyclone. ... The larger end connects to the outside of the SDP, and the smaller end allows the 5" hose to connect to it.
thingiverse
A simple support plate modeled to fit the dust deputy where it attaches to a 5 gallon bucket lid. ... Installing this underneath the lid will allow for additional support since a lot of lids are somewhat flimsy.
thingiverse
Adaptor Kit to mount a Dust Deputy on top of a Fein Turbo Vacuum using 2 1/2" hose. Parts needed: Shop Vac brand 2 1/2" vacuum hose. Dust Deputy DIY 5 gallon or 3.5 gallon bucket with lid. Fein Turbo Vac. The 90degree and Arc...
prusaprinters
This is a right angle fitting that attaches to the top of a Dust Deputy cyclone separator. This fitting makes it less likely to kink your vacuum hose. ... For standard 2 ½ inch vacuum hose.</p><p>I printed it in one piece in PETG with...
thingiverse
Connector between Super Dust Deputy and the 5-4-4 Wye connector that came attached to the inlet of my Harbor Freight 2HP dust collector. The slightly larger side with the taper goes inside the wye, and the narrower goes into the SDD inlet. For me,...
thingiverse
I already have a dust deputy and it works great for everything except fine dust. ie. concrete dust and drywall dust. I decided to try using a Dyson because I think the cyclone is more geared toward fine dust, and its much easier to change out the...
thingiverse
Customized version of https://www.thingiverse.com/thing:2015939 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2015939
prusaprinters
6.5-Peak HP NXT Wet/Dry Shop Vacuum)-Inlet straight adapter to 2.5" dust collection tubing with band clamp-2.5" dust collection tubing to 1.5" vacuum port attachment Both on an Ender 5+ with Mosquito hot end and 1.0mm nozzle. ...Printed directly on...
thingiverse
Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651